manualshive.com logo in svg

Grizzly G0636X, Руководство пользователя, Страница: 8 / 68

Поделиться
Скачать
Grizzly G0636X Скачать руководство пользователя страница 8

-6-

Model G0636X (Mfd. Since 09/18)

Controls & 

Components

Front Controls

A.  Power Switch:  Disables  ON/OFF  buttons 

when  key  is  turned  to  "0"  position.  Remove 
key to lock switch and prevent unauthorized 
use of machine.

 

IMPORTANT: Locking the power switch with 
the  key  only  restricts  its  function.  It  is  not  a 
substitute  for  disconnecting  power  from  the 
machine when adjusting or servicing.

B.  ON Button: Starts motor only if OFF button is 

popped out and power switch is turned to "1" 
position.

C.  OFF Button: Disables ON button. Enable ON 

button by twisting OFF button clockwise.

D.  Blade Tension Scale: Allows for easy moni-

toring of blade tension.

E.  Blade Tension Handwheel: Tensions blade 

in gradual increments. 

F.  Blade Tracking Window:  Allows  for  easy 

monitoring  of  blade  tracking  (refer  to 

Page 

19). 

G.  Fence, Rail, and Miter Gauge:  Allows  for 

controlled cutting at various angles.

H.  Foot Brake: Cuts power to motor and allows 

bandsaw  blade  to  be  quickly  brought  to  a 
stop. 

Rear Controls

I.  Guide Post Handwheel and Lock Knob: 

Moves    blade  guide  support  quickly  to  the 
desired  height  on  the  guide  post;  locks  set-
ting (refer to 

Page 34).

J.  Quick Release Blade Tension Lever: 

Releases  blade  tension  for  quick  blade 
changes. 

K.  Blade Tracking Knob and Lock Lever: 

Moves and locks blade tracking.

Figure 1. Front controls.

Figure 2. Rear controls.

I

K

M

J

L

D

A
B

C

E

F

G

H

L.  Table Tilt Lock Lever: Locks or unlocks the 

table at the current angle.

M.  Table Tilt Handwheel: Tilts  the  table  up  to 

5º to the left or 45º to the right (refer to 

Page 

33).

Содержание G0636X





































































Отзывы:

Нет отзывов