Grizzly G0636X Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 68

Grizzly G0636X Скачать руководство пользователя страница 21

Model G0636X (Mfd. Since 09/18)

-19-

Blade Tracking

Personal injury or death

can occur if the machine

starts while your hand

is touching the bandsaw

wheel during tracking

adjustments. Disconnect

power from the bandsaw

before performing blade

tracking adjustments.

The  blade  tracking  is  primarily  affected  by  the
tilt  of  the  upper  wheel,  also  known  as  "Center
Tracking"; and the alignment of both wheels, also
known  as  "Coplanar  Tracking."  (For  Coplanar
Tracking, see the

Wheel Alignment instructions

on

Page 50.)

The wheels on this bandsaw were aligned at the
factory, so Center Tracking is the only adjustment
that needs to be performed.

To center track the blade:

1. DISCONNECT MACHINE FROM POWER!

2. Make sure upper and lower blade guides are

adjusted away from blade (see

Page 24).

3. Move quick tension lever to tightened posi-

tion and turn blade tension handwheel until
blade tension matches the mark on the blade
tension scale for appropriate blade thickness
(see

Figure 12).

Blade Centered

on Peak of Crown

Blade

Centered

on

Wheel

CENTER TRACKING

Wheel

Figure 13. Center tracking profiles.

4. Open upper wheel cover.

5. Spin upper wheel by hand at least three times

and watch how blade rides on the crown of
the wheel. Refer to

Figure 13 for an illustra-

tion of this concept.

— If the blade rides in the center of the upper

wheel and is centered on the peak of the
wheel crown, then the bandsaw is already
center tracked properly and no further
adjustments are needed at this time.

—If the blade does not ride in the center of

the upper wheel and is not centered on the
peak of the wheel crown, then continue
with the following steps.

Figure 12. Blade tensioning controls.

Blade Tension

Handwheel

Blade Tension

Scale

The cast iron spokes may have sharp edges

and the blade teeth may extend beyond the

edge of the wheel, creating a laceration

hazard. Be careful when turning the wheels

by hand.

«
...
19
20
21
22
23
...
»

Содержание G0636X





































































Отзывы:

Нет отзывов