manualshive.com logo in svg

Greyline OCF 6.1, Руководство пользователя

Поделиться
Скачать
Greyline OCF 6.1 Скачать руководство пользователя страница 26

 

Page 26 

OCF 6.1 Open Channel Flow Monitor 

TYPICAL SENSOR POSITIONING 
FOR FLUMES AND WEIRS 

 

Always refer to the flume or weir manufacturer’s instructions for correct measurement point upstream 
from the flume or weir. Location of the sensor is critical for accurate flow measurement. 

If manufacturer’s instructions are not available, the following guidelines are generally accepted. 

1. PARSHALL FLUME:  
 
Position the sensor at 2/3 Approach as 
illustrated above. Sensor height must be 
8" (203 mm) or more above the highest 
water level. 
 
 
2. PALMER BOWLUS FLUMES: 
 
Position the sensor at ½ the flume 
Diameter upstream from the throat of 
the flume. Sensor height must be 8" 
(203 mm) or more above the highest 
water level. 
 
 
3. V-NOTCH WEIRS 
 
Position the sensor at 3 x maximum Head 
upstream from the weir plate. Sensor height 
must be 8" (20.3 cm) or more above the 
highest water level.  
 
 
STILLING WELLS 
 
Stilling wells are recommended to reduce the effects of turbulence as water flows through the flume or 
weir. The OCF 6.1 sensor is centered over the stilling well. Sensor height must be 8" (203 mm) or 
more above the highest water level. The well must be kept clean of sediment and deposits on the side 
walls. 

 

 

Содержание OCF 6.1


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды