background image

 
 
 

Rotary Mulcher RM 232 

Safety 

 

The instructions derive from the current national accident prevention regulations that the 
owner or the operational manager must comply with.  
 
In the same way as the current traffic laws, of course, must be complied with if the 
machine is used on public roads.

 

Warnings, prohibitions and instructions 

 

For any kind of work on the tool, it must be disconnected from all 

hydraulics. 

 

 

Only authorized personnel may perform service work on the tool.

 

 

 

Read this instruction manual carefully before using the tool.

 

Safety instructions for maintenance and inspection work 

 

The operator must ensure that all maintenance, inspection and installation work is 
carried out by authorized and qualified professional personnel who, after carefully 
reading the instruction manual, have sufficient knowledge.

 

 

Maintenance and adjustments must be made only when the machine is stopped. The 
procedure for stopping the machine as described in "Stop the tool" must be followed 
unconditionally. 

 

When doing maintenance work on the mounted tool and / or machine, secure with 
suitable support elements. 

 

When replacing work tools with cutting edges, check the hydraulic system for residual 
pressure, any remaining residual pressure is reduced to zero (0). 

 

Use only suitable tools and wear safety work gloves, safety shoes and safety goggles. 

 

Handle the hydraulic oil and grease in compliance with regulations. Be familiarized 
with the safety data sheet (APBA). 

 

Immediately after the completion of work, all safety devices must be installed and 
reactivated. 

 

Before re-use, the items in the "Initial start-up" section from the tractor / vehicle 
manufacturer must be followed unconditionally. 

 

 

Содержание RM 232













































Отзывы: