manualshive.com logo in svg

Gravely 991001-008, Руководство по обслуживанию

Поделиться
Скачать
Gravely 991001-008 Скачать руководство пользователя страница 62

13 - 62

Promaster 100 Briggs/Stratton -16 HP

Installation checkout: Make sure that all switches are in 
their proper position: PTO switch off, Neutral switches 
activated. (T-levers centered).

Step 1: 

Check out the battery. Use a hydrometer on all the 
battery cells to see if one or more is bad. Also use a 
voltmeter to check for proper voltage. Replace the 
battery if necessary and/or charge to proper level.

Step 2:

Use a voltmeter to make sure you have power to 
terminal B in the off position on the back of the key 
switch. If you don’t have power to terminal B, check the 
25-amp fuse or connection at the start solenoid.

Step 3:

With the key switch in the RUN position see that power 
has been transferred to terminals L, and A. Terminal A 
supplies power to the relay (pin 86) and on to the seat 
switch to activate the holding circuit for the time delay, 
and fuel shut off solenoid. Terminal A supplies power to 
the hourmeter and oil PSI light, and brings in charge 
power from the engine to the battery.

Terminal M grounds the key switch with the unit.

Terminal G provides an additional ground for the kill 
circuit of the engine.  

Step 4:

With the key in the START position, power is 
transferred to terminal S, to the first small stud on the 
solenoid, out the other side through the PTO and 
neutral switches to ground for starting.

Содержание 991001-008

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды