manualshive.com logo in svg

Gravely 991001-008, Руководство по обслуживанию

Поделиться
Скачать
Gravely 991001-008 Скачать руководство пользователя страница 30

8 - 30

(Electric/Hydraulic Pump) 

Problem-solving Chart

Electric/Hydraulic Pump Removal

1. Disconnect black ground wire at frame.

2. Remove switch from dash. Leave the three leads 

connected to switch.

3. Clean hydraulic fittings and mark hoses to insure 

proper routing at time of pump installation.

4. Disconnect hydraulic hoses from pump.

NOTE: Support electric/hydraulic lift pump when 
removing mounting bolts.

5. Remove the two mounting bolts and lift pump out 

of unit.

6. Drain hydraulic fluid through reservoir cap.

7. Repair as needed.

Electric Hydraulic Pump Installation

1. Install pump with the two mounting bolts.

2. Reconnect hydraulic hoses. 

3. Install switch into dash with green terminal to the 

top and blue terminal to the bottom.

4. Reconnect black ground wire to frame.

5. Remove cap and service hydraulic reservoir with 

Dextron II or Dextron III to full line. Install cap.

6. Reconnect battery, negative terminal first.

Electric/Hydraulic Pump Switch Replacement

 

1. Remove switch from dash and disconnect the 

three leads.

2. The switch can only be installed one way. Check 

orientation of switch for proper lead hookup.

3. Connect the three leads to the switch—green - top, 

red - middle, and blue - bottom.

4. Install switch into dash. Reconnect the battery, 

negative terminal first and check operation of 
switch.

Hydraulic Hose Removal

1. Clean hydraulic fittings prior to removing hoses.

2. Disconnect hydraulic hose(s) from cylinder end 

first.

3. Disconnect hydraulic hose(s) from pump end.

4. Replace hoses as needed.

Hydraulic Hose Installation

1. Connect hydraulic hose(s) to pump first. 

2. Connect hydraulic hose(s) to cylinder.

3. Connect battery, negative terminal first.

4. Cycle unit up and down a few times to bleed the 

system.

5. Add Dextron II or Dextron III to the full line on the 

reservoir if servicing is needed.

Hydraulic Cylinder Removal

 

1. Clean hydraulic fittings prior to removing hydraulic 

hoses.

2. Disconnect hydraulic hoses. Note orientation of 

hydraulic hoses.

3. Disconnect cylinder from mower lift weldment. 

Note which hole cylinder is connected to.

4. Remove the left side retaining ring from the 

hydraulic cylinder shaft.

5. Support hydraulic cylinder and slide hydraulic 

cylinder shaft out on the right side far enough to 
clear cylinder.

6. Remove cylinder from tractor.

Hydraulic Cylinder Installation

NOTE: Hydraulic ports for fittings need to be facing up.

1. Slide cylinder shaft through hydraulic cylinder and 

out through the left side of tractor frame.

2. Install left side retaining ring on cylinder shaft.

CAUTION: Remove attachment from tractor 
or disconnect attachment at mower lift arm 
prior to working on lift system. Replace 
hydraulic fluid after any maintenance has 
been performed on the lift system.

Observation

Possible Cause

Attachment will not raise.

Discharged battery.

Loose connection to 
solenoid or ground.

Attachment raises slowly.

Hydraulic lines routed 
incorrectly.

CAUTION: Disconnect battery negative 
terminal first.

CAUTION: Disconnect battery negative 
terminal first.

CAUTION: When hydraulic pump is operated 
hydraulic fluid is under high pressure. To 
avoid injury disconnect battery (negative 
terminal first) prior to working on hoses.

CAUTION: When hydraulic pump is operated 
hydraulic fluid is under high pressure. To 
avoid injury disconnect battery (negative 
terminal first) prior to working on hoses.

Содержание 991001-008

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды