manualshive.com logo in svg

Gravely 991001-008, Руководство по обслуживанию

Поделиться
Скачать
Gravely 991001-008 Скачать руководство пользователя страница 18

4 - 18

4.6    STEERING CONTROL NEUTRAL 
ADJUSTMENT

If the unit has excessive creep when the twin T-bar 
control levers are in neutral, adjust as follows.  See 
Figure

 

5

.

1. Stop the engine.

2. Make sure both twin T-bar control levers are in the 

neutral detent.  (This is important).

3. With the unit facing a wall, jack the unit up so that 

both drive wheels are off the ground. (You may 
want to remove the linkage guards).  See Figure 5.

4. Loosen the two 1/4-20 hex bolts holding the neutral 

adjustment weldment.  Loosen the bolts just 
enough so that the weldment can be rotated by 
tapping on one of the bottom corners with a wrench 
or small hammer.

5. Start the engine and run at about half throttle or 

faster. 

6. Tap on one bottom corner or the other of the 

neutral adjustment weldment until the wheel stops 
turning. Try to adjust neutral to the center of the 
neutral band.  Tighten the two 1/4-20 hex bolts.

7. Move the control levers, from forward to reverse 

several times to make sure it is adjusted to neutral.  
Readjust if necessary.

8. Stop the engine.

4.7  T-BAR CONTROL LEVER ALIGNMENT

Refer to Figure 7.

1. Move the control levers to the neutral detent 

position.  Stop the engine.

2. Loosen the 5/16-18 bolt in the clamp at the base of 

each control lever.  (Loosen the bolts just enough 
to rotate the control levers on their shaft with some 
resistance).

3. Position the control levers in the desired location 

and tighten the 5/16-18 bolt on each one.

4. Move the control levers forward and backward as 

far as they will travel to check for interference in 
the instrument panel slots.  If there is interference, 
readjust the neutral position.

4.8  CHECK THE TIRES

Before each use make a visual check of tires.  The 
correct air pressure is 12-15 psi (83-103 kN/m2) for the 
rear tires and 20-25 psi (138-172 kN/m2) for the front 
tires.

4.9  ADJUSTING THE UNIT TO TRACK 
STRAIGHT

There are two main reasons the unit will not track 
straight:

1. Orientation of the T-bar levers is not adjusted 

identically relative to the hydraulic pump neutral 
band.  Each Sunstrand pump has a .031 inch 
diameter orifice in both the forward and reverse 
circuit; the neutral band has some width to it.

2. The tires vary in size and adjusting the air pressure 

slightly can compensate for this.

WARNING: This adjustment requires 
operation of the engine and removal of 
guards.  Use extreme care to avoid contact 
with moving parts and hot surfaces.  Be sure 
rear of unit is well supported and secure 
before starting engine.

Figure 6

1. Speed Control Arm
2. Neutral Adjustment 

Weldment

3. 1/4-20 Hex Bolts

4. Neutral Detent Strap
5. Linkage Guard

OF 1111

1

2

3

4

5

1

1

2

2

Figure 7

1. T-Bar Control Levers
2. 5/16-18 Bolts

OF1100

Содержание 991001-008

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды