Gravely 991001-008 Скачать руководство пользователя страница 19

Страница: 19 / 80

4 - 19

Check the air pressure in each tire before attempting to
make any adjustments.

A. If the unit tends to turn slowly to the right when the

twin T-bar control levers are held in the same
forward position, try some of the following steps
until the unit tracks straight.

1. Adjust the neutral closer to reverse on the left

wheel.

2. Adjust the neutral closer to forward on the right

wheel.

3. Reduce the air pressure slightly in the left tire.

4. Increase the air pressure slightly in the right tire.

B. If the unit tends to turn slowly to the left when the

twin T-bar control levers are held in the same
forward position, try some of the following steps
until the unit tracks straight.

1. Adjust the neutral closer to forward on the left

wheel.

2. Adjust the neutral closer to reverse on the right

wheel.

3. Reduce the air pressure slightly in the right tire.

4. Increase the air pressure slightly in the left tire.

4.10 LEVELING THE MOWER DECK

Promaster 200

The mower deck can be leveled front to rear and from
side to side. These adjustments should be made on a
level surface with the tires inflated to the correct air
pressure.

The mower is leveled from side to side with the slots
where the 4 chains fasten to the mower mounting
brackets. See Figure 8.

1. Level the mower with blocks of equal height such

as pieces of 2 x 4’s.

2. Attempt to raise the mower until the chains on one

side are tight.

3. Loosen the locknuts on the side of the mower deck

where the chains are slack and slide the bolt down
the slot until the chain is tight.

4. Tighten the locknut.

The mower is leveled from front to rear by adjusting the
rod running down each side of the frame.

1. Loosen and screw back the rear hex nut on the

front end of each rod.

2. Turn the front hex nut on each rod until the mower

is leveled. The front of the deck should be slightly
lower (1/8 inch) than the back.

3. Tighten the rear hex nut that was loosened in

step 1.

Promaster 100 and 160

1. Raise the mower by pulling up on handle until two

mower locking pins can be removed.

2. Adjust mower to desired height and reinsert mower

locking pins, being sure to lock them behind the
handle.

3. Now adjust other side to match.

Figure 8 - Promaster 200

1. Rod
2. Rear Hex Nut
3. Front Hex Nut
4. Chain

5. Lock Nut
6. Slot
7. Mower Deck

PF3030

Содержание 991001-008

















































































Результаты поиска

Содержание 991001-008

Отзывы:

Бренды по названию

Популярные бренды

Gravely 991001-008, Руководство по обслуживанию

Результаты поиска

Содержание 991001-008

Отзывы:

Бренды по названию

Популярные бренды