manualshive.com logo in svg

Gravely 991001-008, Руководство по обслуживанию

Поделиться
Скачать
Gravely 991001-008 Скачать руководство пользователя страница 52

13 - 52

13.13  991000 ELECTRICAL

Models 991005, 006

Promaster 100 Kohler Command

Installation checkout: Make sure that all switches are in 
their proper position: PTO switch off, Neutral switches 
activated. (T-levers centered).

Step 1: 

Check out the battery. Use a hydrometer on all the 
battery cells to see if one or more is bad. Also use a 
voltmeter to check for proper voltage. Replace the 
battery if necessary and/or charge to proper level.

Use a voltmeter to make sure you have power to 
terminal B in the off position on the back of the key 
switch. If you don’t have power to terminal B, check the 
30-amp fuse.

Step 2:

With the key switch in the START position see that 
power has been transferred from terminal B to terminal 
A. Terminal A supplies power to the PTO switch, 
neutral switches, and terminal S2 to crank the engine.

Power is also routed through the diode to activate start/
kill relay and provide power to the fuel solenoid to keep 
the engine running.

Step 3:

With the key in the RUN position, verify power has 
been transferred to terminal A. Terminal A supplies 
power to the seat relay (terminals 30 & 86) and to the 
seat switch.

From the seat relay, power is transferred to the PTO 
switch, start/kill relay and fuel solenoid to keep the 
engine running.

NOTE: The engine kill circuit is connected to terminal 
87A of the relay. The engine will shut down when 
power at the relay is stopped or interrupted.

Clutch Check:

Remove clutch lead from the PTO. Check clutch with a 
digital volt meter for field resistance to see if coil is 
good (2.98 OHMS ± 5%). Current amperage is 4.03. If 
reading is out of spec., high or low, replace clutch. 
Readings will be affected when clutch is hot.

Содержание 991001-008

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды