manualshive.com logo in svg

Gravely 991001-008, Руководство по обслуживанию

Поделиться
Скачать
Gravely 991001-008 Скачать руководство пользователя страница 45

13 - 45

Voltage Measurement

There are two basic rules to be remembered when 
using a voltmeter. A voltmeter measures the voltage 
difference between the test leads and the voltmeter is 
always connected across the circuit under test.

Current Measurement

The two rules to remember when measuring current 
with an ammeter are; an ammeter measures the cur-
rent that flows through the meter, and to measure cur-
rent an ammeter must be connected into the circuit.
The latter rule means that the circuit must be opened, 
and the ammeter wired into it. Because this procedure 
is usually difficult, an ammeter is seldom used for trou-
bleshooting.

Resistance Measurement

An ohmmeter is used to make resistance measure-
ments and to check continuity through wires and elec-
trical components.
There is one rule to keep in mind when using an ohm-
meter. The ohmmeter has a self contained battery and 
requires no electrical power. Using the ohmmeter on a 
circuit that has power applied may result in damage to 
the meter.

IMPORTANT: Disconnect the equipment battery when 
making Ohmmeter test or damage to the Ohmmeter 
may result.

IMPORTANT: An ohmmeter reads the resistance of 
whatever component is connected between the test 
leads. It can be used to check wires, coils, light bulbs, 
or any item that conducts current.

13.3  BATTERY

When charging battery, remove it from unit first. Keep 
batteries out of reach of children. ALWAYS follow 
information provided on battery by battery 
manufacturer. Lead acid batteries generate explosive 
gases. Severe chemical burns can result from 
improper handling of battery electrolyte. Wear safety 
glasses and proper protective gear when handling 
batteries to prevent electrolyte from coming in contact 
with eyes, skin or clothing.

Battery Electrolyte First Aid

External contact: Flush with water.

Eyes: Flush with water for at least 15 minutes and get 
medical attention immediately!

Internal contact: Drink large quantities of water. 
Follow with Milk of Magnesia, beaten egg or vegetable 
oil. Get medical attention immediately!

IMPORTANT: In case of internal contact, DO NOT 
induce vomiting!

WARNING: ELECTRIC SHOCK may result in 
injury and/or damage to unit.

DO NOT allow tools or other objects to come 
into contact with both terminal at the same 
time. ALWAYS remove Negative (-) Cable first 
to reduce risk of sparks when removing bat-
tery. ALWAYS connect Positive (+) Cable first, 
then connect Negative (-) Cable when install-
ing battery.

WARNING: EXPLOSIVE GASES can result 
in serious injury or death. ALWAYS keep open 
flames, sparks, or smoking materials away 
from battery.

POISONOUS BATTERY FLUID contains sul-
furic acid and its contact with skin, eyes or 
clothing can cause severe chemical burns. 
ALWAYS wear safety glasses and protective 
gear near battery.
DO NOT TIP any battery beyond 45 degree 
angle in any direction.
ALWAYS KEEP BATTERIES OUT OF 
REACH of children.

WARNING: REVERSE CONNECTIONS may 
result in sparks which may result in injury. 
ALWAYS connect/disconnect cables in proper 
order.

Содержание 991001-008

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды