background image

IMPORTANT SAFETY 

INSTRUCTIONS 

WARNING -  When using this product basic precautions should 
always be followed, including the following: 

1.

 

Read all the instructions before using the product. 

2.

 

To reduce the risk of injury, close supervision is 
necessary when this product is used near children. 

3.

 

Know how to stop the product and bleed pressures 
quickly.  Be thoroughly familiar with the controls. 

4.

 

Stay alert - watch what you are doing. 

5.

 

Do not operate the product when fatigued or under 
the influence of alcohol or drugs. 

6.

 

Keep operating area clear of all persons. 

7.

 

Do not overreach or stand on unstable support. 
Keep good footing and balance at all times. Use 
only certified scaffolding when necessary. 

8.

 

Follow the maintenance instructions specified in the 
manual. 

9.

 

Do not operate without eye protection. 

10.

 

Follow the maintenance instructions specified in the 
manual. 

11.

 

Use only Goodway recommended attachments.  

12.

 

BURN HAZARD:  

Do not touch the boiler housing 

or metal part of wand when operating unit  in the 
hot wash mode.  The use of insulated gloves will 
help avoid accidental burns.

 

WARNING - Risk of Injection or Injury - Do Not Direct 
Discharge Stream At Persons.  This product is to be used only by 
trained operators. 

Содержание HPW-1000






































Отзывы: