background image

“NEO” TV SATELLITE ANTENNAS

113

www.glomex.it

ENGLISH

For further information, please address to the
GLOMEX Service Centre (see section “Technical
Support”).

8. The equipment does not find

the satellite (the led on the
control unit is red)

- the satellite signals are

obstructed by masts of other
boats, bridges, on-board
equipment, etc.

- move the boat to allow an

unobstructed view for the
antenna or correctly position
the antenna on the boat

- the boat is outside the signal

coverage area

- go back within the coverage

area; refer to the footprints of
the coverage areas on page

108

 in this manual

- the boat is heaving within the

first 60 seconds after turning
on the equipment

- bad weather conditions

- turn off the equipment for 10

seconds, turn it on again and
make sure that the boat is
still or moves in a straight line
during the first 60 seconds
after being turned on

- inner failure

- contact the Service Centre

- wrong SKEW adjustment

- adjust the SKEW by following

the instructions on page 

87

9. The equipment does not find

the satellite (the led on the
control unit flashes alter-
nately red and orange)

- the satellite signals are

obstructed by masts of other
boats, bridges, on-board
equipment, etc.

- move the boat to allow an

unobstructed view for the
antenna

- the  equipment  software  is

not up to date

- please contact the Service

Centre to ask for the software
update by SD card

- wrong SKEW adjustment

- adjust the SKEW by following

the instructions on page 

87

10. Disturbed images

- failure of the receiver

- refer to the user manual of

the receiver for support,
spare parts and warranty
conditions.

11. Confused, incomplete and

obstructed images

- condensate or rain on the

radome, which can disturb
the signal

- remove the condensate

deposits from the radome with
a fresh water jet (not under
pressure)

- bad weather conditions

- periodically apply a liquid

detergent suitable for dishes
(no alcohol-based deter-
gent) to the radome surface
and let dry up

- wrong SKEW adjustment

- adjust the SKEW by following

the instructions on page 

87

12. The decoder blocks

- alternating current fluctua-

tions

- refer to the user manual of

the receiver for support

Содержание NEO dCSS Saturn



























































Отзывы: