Gill WindSonic Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 72

background image

WindSonic Doc No 1405 PS 0019 Issue 28 November 2019

37

Y2 nnn Setting, User Set Fixed Analogue Output level in an error mode.

The unit will output a fixed Voltage (T1 setting) or fixed milli-amp (T5/T3 settings) signal
on the analogue output with a value depending on the Y2 nnn setting.

nnn is user-selectable value between 000 to 200.

Scale factor for fixed voltage output is 0.025V.

Scale factor for fixed current output is 0.1mA.

Therefore:-

nnn value = Required fixed Error Voltage/0.025 (voltage output setting T1).

nnn value = Required fixed Error Current/0.1 (current output settings T5/T3).

Under data error conditions then by setting the unit for Y2 configuration the analogue
outputs will read a user set error value for the period of the error condition as follows with
the unit in Polar Continuous Output and 0-5v (T1), 0-20mA (T5) and 4-20mA (T3).

Wind Speed

Condition

Channel 1 Speed

Channel 2 Direction

Digital Error
Code Output
e.g. 01, 02, 04 etc

Error Condition

nnn x 0.025 v (T1 setting).

Error Condition

nnn x 0.025 v (T1 setting).

Error Condition

nnn x 0.1mA. (T5 & T3 setting)

Error Condition

nnn x 0.1mA. (T5 & T3 setting)

Y3 nnn setting Analogue Output cycles to a user determined level in an error mode.

Under data error conditions the analogue outputs will switch back and forth between a user
determined level (voltage or current) with a value depending on the Y3 nnn setting.

nnn is user-selectable value between 000 to 200.

Scale factor for upper voltage output is 0.025V.

Scale factor for fixed current output is 0.1mA.

Therefore:-

nnn value = Required Error Voltage/0.025 (voltage output setting T1).

nnn value = Required Error Current/0.1 (current output settings T5/T3).

The following table summarises the above reporting conditions with Analogue Outputs set
for Polar Continuous Output and 0-5v (T1), 0-20mA (T5) and 4-20mA (T3).

Wind Speed Condition

Channel 1 Speed

Channel 2 Direction

Digital Error Code

Output e.g. 01, 02, 04

etc.

Cycle 0 – set v – 0 v

at output rate

Cycle 0 – set v – 0 v

at output rate

Cycle 0 – set mA – 0 mA

at output rate

Cycle 0 – set mA – 0 mA

at output rate

Cycle 4 – set mA – 4 mA

at output rate

Cycle 4 – set mA – 4 mA

at output rate

«
...
36
37
38
39
40
...
»

Содержание WindSonic









































































Отзывы:

Нет отзывов

Похожие инструкции для WindSonic

Бренд: Atomos Страницы: 4

YPP-100 Light Piano

Бренд: Yamaha Страницы: 54

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 56

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 32

Бренд: DeltaOHM Страницы: 26

Бренд: Alfa Laval Страницы: 18

Бренд: Van Walt Страницы: 2

Бренд: E+E Elektronik Страницы: 20

Бренд: Brooks Страницы: 64

Бренд: brena Страницы: 26

Бренд: Alpes Lasers Страницы: 41

Бренд: Thermo Scientific Страницы: 56

Бренд: Velleman Страницы: 15

Бренд: Fluke Страницы: 6

Бренд: Omega Страницы: 16

Бренд: A&D Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды