Gill WindSonic Скачать руководство пользователя страница 9

Страница: 9 / 72

WindSonic Doc No 1405 PS 0019 Issue 28 November 2019

5 SPECIFICATION

This Specification relates to WindSonic Option 1, 2 and 3 WindSonic Sensors fitted
with a Red Tab and WindSonic 75 Option 1, 2 and 3 fitted with an Orange tab (fitted
adjacent to the North Marker arrow).

Output

Units of measure

Metres/second (m/s),

Knots, Miles per hour (mph),

Kilometres per hour (kph), Feet per minute (fpm)

Output frequency

0.25, 0.5, 1, 2, or 4 outputs per second

Digital

Analogue

Parameters

Polar - Speed and Direction
UV - 2 axis, signed Speed
NMEA Speed and Direction
Tunnel - U speed & U Polarity

Polar - Speed and Direction
UV - U Speed and U Polarity
NMEA – Speed and Direction
Tunnel - U Speed & U Polarity

Wind Speed

0 – 5m/s, 0 – 10m/s, 0 – 20m/s,

Range

0 – 60m/s WindSonic
0 - 75m/s WindSonic 75

0 – 30m/s, 0-40m/s, 0 – 50m/s,
0 – 60m/s, 0-80m/s.

Accuracy



2% (at 12m/s)



2% (at 12m/s)

Resolution

0.01 m/s

10 bits

Wind Direction

Range

0 - 359



359



Or 0 - 539



(Wraparound mode)

Accuracy





(at 12m/s)





(at 12m/s)

Resolution



Analogue output
formats (not
Windsonic 75)

0-5V
4-20mA
0-20mA



1% of full scale N.B. Analogue output impedance = 1KΩ (V out)

Load resistance between the Analogue outputs (Pins 8 & 9) and Signal
Ground (Pin 1) must be <= 300 ohms, including cable resistance.

Digital output
formats

Gill

Continuous or Polled (output on request by host system)
Polar (Speed and Direction) or UV (2 axis, signed Speed)

Marine – NMEA

NMEA 0183 version 3

Communication
formats

WindSonic Option 1

RS232

WindSonic Option 2

RS232, RS422, RS485 (2 wire Point to Point)

WindSonic Option 3
Baud Rate

RS232, RS422, RS485 (2 wire Point to Point), and Analogue
2400, 4800, 9600, 19200, 38400 Baud Rates

Anemometer status

Status OK and Error codes included in output message

Содержание WindSonic









































































Результаты поиска

Содержание WindSonic

Отзывы:

Бренды по названию

Популярные бренды

Gill WindSonic, Руководство пользователя

Результаты поиска

Содержание WindSonic

Отзывы:

Бренды по названию

Популярные бренды