Gill WindSonic Скачать руководство пользователя страница 33

Страница: 33 / 72

WindSonic Doc No 1405 PS 0019 Issue 28 November 2019

9.4 NMEA Format (NMEA status Codes)

The

Wind Direction, Wind Speed,

and

Units

are as described in Section 9.1.

The

Instrument Type

– IIMWV - is a mnemonic for Integrated Instrument Mean Wind

direction & Velocity.

The

Status

codes are:

cceptable measurement

oid measurement

A typical WindSonic configuration suitable for NMEA (See Section 10):

M5, U1, O1, L1, P1, B2, H1, NQ, F1, E2, T1, S4, C2, G0, K50

Consult specification NMEA 0183 version 3 (available on the web) for complete interface
details.

The WindSonic can also be set for the alternative start of string NMEA format WIMWV
(Mode 14, which is a Mnemonic for: -

Wind Instrument Mean Wind direction and Velocity.

The string format will appear as above but with WIMWV at the start of the string.

$ IIMWV, 120, R, 002.10, M, A*5D

Wind direction

Wind speed

Units

Status

Start of

string

Instrument
type

Relative wind measurement

Check sum

Содержание WindSonic









































































Результаты поиска

Содержание WindSonic

Отзывы:

Похожие инструкции для WindSonic

Бренды по названию

Популярные бренды

Gill WindSonic, Руководство пользователя

Результаты поиска

Содержание WindSonic

Отзывы:

Похожие инструкции для WindSonic

Бренды по названию

Популярные бренды