Gill WindSonic Скачать руководство пользователя страница 55

Страница: 55 / 72

WindSonic Doc No 1405 PS 0019 Issue 28 November 2019

Ox - ASCII Output Format

Item

Options

Command

ASCII output format

Comma separated format (CSV)

Fixed field

Example data string for CSV data changing to low wind less than 0.05m/s (set for K50) and
error status code condition.

Q,156,000.05,M,00, 19

Q,,000.04,M,00, 2A (low wind, no direction figure output at 0.04m/s or lower).

Q,100,000.09,M,00, 16

Q,,,M,04, 24 (error data, no figures output in wind fields).

Example data string for Fixed Field data changing to low wind less than 0.05m/s (set for
K50) and error status code condition.

Q,160,000.05,M,00, 1C

Q,160,000.04,M,00, 1D (low wind, last direction figure at 0.05m/s or above retained).

Q,170,000.06,M,00, 1E
Q,999,999.99,M,04, 0A (error data, wind fields padded with 9’s).

Px to Pxx - Output Rate

Item

Options

Command

Output rate

1 per second

2 per second

4 per second

1 reading every 4 seconds

1 reading every 2 seconds

P20

P21

Q - Measurement Mode

See Section 10.5.

Содержание WindSonic









































































Результаты поиска

Содержание WindSonic

Отзывы:

Бренды по названию

Популярные бренды

Gill WindSonic, Руководство пользователя

Результаты поиска

Содержание WindSonic

Отзывы:

Бренды по названию

Популярные бренды