Gill WindSonic Скачать руководство пользователя страница 25

Страница: 25 / 72

WindSonic Doc No 1405 PS 0019 Issue 28 November 2019

7.10 Using the Analogue Output (Option 3)

Notes

If the Current output is used, the total output load

MUST

be below 300 ohms, including

the cable resistance.

The current output loads must be returned to Signal Ground.

Reconfiguration of the analogue output requires a digital connection (

See sections 9 &

In addition, the digital output can be connected if required using RS232, 422 or 485
point to point, as shown in the previous sections.

WindSonic

9 Way circular connector

Data logger or

Chart recorder

Signal names

Pin

nos.

Cable – 3 twisted pairs

Signal names

Analogue Channel 1

(Speed)

Analogue Channel 2

(Direction)

Analogue Channel 1

Analogue Channel 2

Signal Ground

(Analogue Return)

Signal Ground

Do NOT connect

at this end

N/A

Screen and drain wires

Chassis ground

V supply -

–

DC Power supply

(See Para 7.3.2)

Содержание WindSonic









































































Результаты поиска

Содержание WindSonic

Отзывы:

Бренды по названию

Популярные бренды

Gill WindSonic, Руководство пользователя

Результаты поиска

Содержание WindSonic

Отзывы:

Бренды по названию

Популярные бренды