Gill WindSonic Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 72

background image

WindSonic Doc No 1405 PS 0019 Issue 28 November 2019

5

1 FOREWORD

Thank you for purchasing the WindSonic manufactured by Gill Instruments Limited. The
unit has no customer serviceable parts and requires no calibration or maintenance. To
achieve optimum performance we recommend that you read the whole of this manual before
proceeding with use. Do NOT remove black “rubber” transducer caps.

Gill products are in continuous development and therefore specifications may be subject to
change and design improvements without prior notice.

The information contained in this manual remains the property of Gill Instruments and
should not be copied or reproduced for commercial gain.

2 INTRODUCTION

The Gill WindSonic wind sensor is a very robust, lightweight unit with no moving parts,
outputting wind speed and direction. The units of wind speed, output rate and formats are all
user selectable.

The WindSonic can be used in conjunction with a PC, data logger or other device, provided
it is compatible with one of the standard communication formats provided by the
WindSonic.

WindSonic (option 2 or 3 only) is designed to connect directly to the Gill WindDisplay unit
to provide a complete wind speed direction system.

WindSonic (options 1, 2 and 3) may be configured using Wind software which is available,
free of charge, from the Gill website

www.gillinstruments.com

. The output message format

can be configured in Gill format, in Polar or UV (2-axis) format, and to either Polled
(requested by host system) or Continuous output. Alternatively, it can be configured in
NMEA (0183 Version 3). These are described in Section 9 MESSAGE FORMATS.

WindSonic (option 4) SDI-12 may not be re-configured in any Gill output format and format
is SDI-12 (V1.3) and described in Section 14 SDI-12 COMMANDS.

3 FAST TRACK SET-UP

If you are in a hurry to try out the WindSonic (options 1, 2 or 3) and are familiar with Gill
equipment and coupling to a PC using RS232, go to the following sections:



Section 7 INSTALLATION



Section 9 MESSAGE FORMATS



Section 10 CONFIGURING

After you have successfully set up the WindSonic, we strongly advise that you then go back
and read the rest of the manual to ensure that you get the best results from the WindSonic.

«
...
4
5
6
7
8
...
»

Содержание WindSonic









































































Отзывы:

Нет отзывов

Похожие инструкции для WindSonic

Vigilant ELM Series

Бренд: Eagle Eye Power Solutions Страницы: 9

Бренд: Lumel Страницы: 32

Бренд: Yamaha Страницы: 48

Бренд: Hanna Instruments Страницы: 2

Бренд: MULTISPAN Страницы: 2

miniSERIES Series

Бренд: Valeport Страницы: 25

Seeker 400 Series

Бренд: General Страницы: 24

Бренд: shelyak Страницы: 45

Бренд: NIEUWKOOP Страницы: 2

Бренд: BERG Страницы: 23

PMD Analyzer 5500B

Бренд: EXFO Страницы: 4

Бренд: VECTECH Страницы: 10

Proline Promass 200

Бренд: Endress+Hauser Страницы: 12

Backsense BS-9000-WD

Бренд: Brigade Страницы: 42

Бренд: Cargo Data Страницы: 3

Бренд: GeoMax Страницы: 14

Бренд: Badger Meter Страницы: 20

Бренд: Chauvin Arnoux Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды