GILES EOF-20 Скачать руководство пользователя страница 82

Страница: 82 / 113

Fryer Operation

EOF 10-10/20

5-05.

Using the Optional Stainless Filter Media Screen (SSFS)

This section describes use and care of the renewable, stainless steel, Filter Screen (SSFS). The SSFS is a direct

replacement for paper filter media that can cleaned and reused many times. It is an optional item

(Giles #41017)

that can be ordered with new units, or purchased later as a filter paper alternative.
1. Place the SSFS into the Filter Pan same as filter paper.

DO NOT use filter

paper and the Screen at the same time

2. Be sure that the edge gasket is flat against Pan bottom. Position the

Hold-down Frame and lock into place with the locking levers. Levers may

not fully close when using the Screen ... this will not affect performance.

3. For best filtering results, always use an appropriate filter aid, such as

Giles

#72004 Filter Powder

. Distribute the prescribed amount evenly over the

surface, same as with filter paper.

4. After performing a regular filtering cycle, see

Section 5-04, Filtering Used

Cooking Oil,

clean accumulated filter sediment from the SSFS surface with

the supplied Crumb Shovel, or other suitable utensil, and discard. It

might be necessary to remove the Screen to brush remaining residue

from its surface.

5. If Screen is removed, do not allow filter residue to fall into the Filter Pan

bottom and be sure to wipe any residue from the edge gasket. Reinstall

screen with the soiled side up.

1. It is not necessary to wash the SSFS Filter Screen after every filtering

cycle.

2. On a weekly basis, remove the SSFS Screen and clean it in a sink, using

ONLY

hot water and a soft bristle brush.

DO NOT USE SOAP or OTHER

CLEANERS

when washing the Screen. Doing so may affect oil life and

quality. Soap residue cannot be completely rinsed from the screen, and it

will eventually be transferred to cooking oil during subsequent filter

cycles.

DO NOT USE OVEN CLEANERS or CAUSTIC PRODUCTS

to clean the

Screen. These chemicals will damage the silicone edge gasket, and

residue will be transferred to cooking oil.

5. Before reinstalling the clean SSFS in the Filter Pan, shake off excess water

and dry with a clean towel. Be certain screen is completely dry before

using. If possible, it is best to allow screen to dry overnight.

6. Take care not to cut or tear the silicone edge gasket. Inspect the Screen

weekly for damage, such as fraying, holes, damaged gasket, etc. A

damaged screen should be removed from service and replaced

immediately.

5-05.1

Cleaning the Stainless Filter Screen Media (SSFS

)

Содержание EOF-20


















































































































Результаты поиска

Содержание EOF-20

Отзывы:

Похожие инструкции для EOF-20

Бренды по названию

Популярные бренды

GILES EOF-20, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание EOF-20

Отзывы:

Похожие инструкции для EOF-20

Бренды по названию

Популярные бренды