GILES EOF-20 Скачать руководство пользователя страница 78

Страница: 78 / 113

EOF 10-10/20

Fryer Operation

10. Used cooking oil will begin to circulate

⑨

through the filter media in

the Pan and return to the fry Vat. Leave the Drain Valve open to allow

oil to continually circulate through the system for about 5 minutes.

During this time, remove the Crumb Screen from the Vat and use the

various provided brushes to scrub the vat walls and heating elements,

allowing residue to be flushed into the Filter Pan.

11. After about 5 minutes, replaced the Crumb Screen if removed, push in

and lock the Drain Valve Handle

⑩

in the

CLOSED

position and allow

the Vat to refill. When all oil has been pumped back to the vat, air

bubbles will appear at the pump discharge inside the vat.

5-03.

Filtering Used Cooking Oil - Continued

12. After the Vat has refilled, place the Pump Switch

⑪

in the

OFF

position.

13. Position the Pump Oil Return Lever

⑫

on the unit being

filtered to the

CLOSE

position.

14. Be sure the Fry Vat contains the proper level of cooking oil ...

add if needed.

15. Fryer unit should now be ready to

PREHEAT

back to the

Controller setpoint temperature. If

FORCE FILTER

, the

unit will remain in Filter Mode until the registered actual oil

temperature drops below

275

Typically, the filtering

process will reduce oil temperature sufficiently to reset the

Filter Mode lockout.

15. To continue cooking, See

Section 5-02, Cooking

Procedure

To discontinue cooking, See

Section 5-06,

Normal Shut-Down

Содержание EOF-20


















































































































Результаты поиска

Содержание EOF-20

Отзывы:

Похожие инструкции для EOF-20

Бренды по названию

Популярные бренды

GILES EOF-20, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание EOF-20

Отзывы:

Похожие инструкции для EOF-20

Бренды по названию

Популярные бренды