GILES EOF-20 Скачать руководство пользователя страница 45

Страница: 45 / 113

EOF 10-10/20

4-03.

Heating Element Test

1. Follow steps shown in

Section 4-01

2. Be sure Power Switch is in the

OFF

position.

3. Liberally dampen a sponge with water and wipe down the

Heating Element

①

, leaving them visibly wet.

4. Place the Power Switch

②

in the

position.

EOF-20:

Wait for the Controller to power up, sound the alarm

signal and show the message

POWER FAILURE PRESS [START]

TO PREHEAT

on the

OLED Display

and

[HOLD]

on the

7-Segment

Display

③

6. Press the

[START]

key

④

... the alert signal will silence, and the

Controller wil indicate

PREHEAT

EOF10-10:

Message

START WHICH SIDE ... [4]=LEFT, [5]=BOTH,

[6]=RIGHT

is shown on the

OLED Display

... select

BOTH

[keypad 5]

then Controller will indicate

PREHEAT

7. Set the Heat Switch

⑤

to the

HEAT

position

(both switches on

EOF10-10)

. The

HEAT

light(s) should turn on. Leave switch(s) in

the

HEAT

position

NO MORE THAN 10 to 12 SECONDS

Note:

During this time, should the

HEAT

light turn off, an alarm

sound and the

OLED Display

show a

MAX ELEMENT TEMP or

LOW OIL LEVEL

error; return Power Switch to the

OFF

position

and proceed on to the next step.

8. Return Heat Switch

⑤

to the

OFF

position.

9. The moisture on the heating elements should quickly dry and

heat should be felt rising from the Vat. Proceed to

Section 4-04

If the moisture does not dry within 15-30 seconds, or no heating

is detected, refer to the Troubleshooting procedure in

Section 7-

01.

The following test will ensure the Heating Element is being powered.

Perform this test on each Fry Pot.

EOF-10-10

EOF-20

Installation Checkout & Prep

Heating Elements become extremely hot when energized! Any skin contact with them

may result in severe burns.

Содержание EOF-20


















































































































Результаты поиска

Содержание EOF-20

Отзывы:

Похожие инструкции для EOF-20

Бренды по названию

Популярные бренды

GILES EOF-20, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание EOF-20

Отзывы:

Похожие инструкции для EOF-20

Бренды по названию

Популярные бренды