GILES EOF-20 Скачать руководство пользователя страница 8

Страница: 8 / 113

vii

Safety

EOF 10-10/20

Safety Overview

Safety

Hazard Alert Symbols

are used in conjunction with key words

DANGER, WARNING

, and

CAUTION

alert user to potential personal injury hazards and/or poor operating practices. These will immediately precede pre-

cautionary measures pertaining to such hazards or practices. Adhere to all safety messages which follow these sym-

bols to avoid possible injury, or even death. Failure to do so may also void the factory warranty.

The instructions contained in this manual have been prepared to aid you in learning the proper procedures for

installing, operating and servicing your new

Giles Model EOF Series Electric Fryers

Throughout this manual, safety precautions are identified through the use of the safety alert symbol and three sig-

nal words:

DANGER, WARNING

and

CAUTION

. All safety alert information precedes the tasks to which they apply.

Suggested, recommended, or other noteworthy information is identified through the use of

NOTES

, or be noted as

IMPORTANT!

. Additionally, certain words are used to indicate a specific meaning or to add emphasis as follows:

Shall:

understood to be mandatory.

Should:

understood to be advisory.

May:

understood to be permissive.

Will:

indicates a future event or condition to occur.

•

Indicates an imminently hazardous situation which, if not avoided, will result in serious personal injury, even

death.

•

Indicates a potentially hazardous situation which, if not avoided, could result in serious injury, even death.

•

Indicates a potentially hazardous situation which, if not avoided, may result in minor to moderate injury. This

notification is also used as an alert to unsafe practices.

•

If used without the safety alert symbol, indicates a potentially hazardous situation which, if not avoided, may

result in equipment and/or property damage, and may void the factory warranty.

NOTE or IMPORTANT!

•

Identifies suggested, recommended, or other important information.

Содержание EOF-20


















































































































Результаты поиска

Содержание EOF-20

Отзывы:

Похожие инструкции для EOF-20

Бренды по названию

Популярные бренды

GILES EOF-20, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание EOF-20

Отзывы:

Похожие инструкции для EOF-20

Бренды по названию

Популярные бренды