Ghost Controls TDS2 Скачать руководство пользователя страница 8

Страница: 8 / 68

S Y S T E M S A F E T Y

2 0 2 1

VEHICULAR GATE STANDARD

We recommend that all vehicular gates be constructed

and installed in accordance with Active Standard ASTM

F2200, Standard Specification for Automated Vehicular

Gate Construction. For more information on this stan-

dard, contact ASTM directly at

www.astm.org/Standards/

F2200.htm

WARNING SIGNS

The included warning signs must be installed on both the

inside and outside of the gate.

GHOST CONTROLS 2016

1. Persons are to keep clear! The gate is able

to be moved without prior warning.

2. DO NOT let children operate the gare or

play in the gate area.

3. Persons are to operate the gate only when

the gate area is in sight and free of people

and obstructions.

4. Persons are to read the user’s manual and

safety instructions.

WARNING

ALARM

Your GHOST CONTROLS

Gate Operator system

includes an audible alarm. This alarm will continue to

sound for 5 minutes when two sequential obstructions

are detected during gate travel per UL325 safety

standards or until one of the following occurs:

■

The gate operator receives an intended signal from a

hard wired entry/exit source such as a push button or

a wired keypad. Note that wireless transmitters and

wireless keypads cannot deactivate the alarm.

■

The gate operator system is powered off and then on

again at the main power switch in the control box.

NOTE

The alarm may also be used as audio feedback for other

modes of operation under normal operation.

SWING GATE PROTECTION AND

ENTRAPMENT ZONES

As specified in Gate Operator Safety Standard, UL325

(30A 1.1) 7th Edition, all gate operators must include

two independent means of entrapment protection. All

GHOST CONTROLS

Automatic Gate opener systems

meet this standard as indicated on the product packaging

through the following:

TYPE A Inherent.

Number one above AND either of the following two

options:

TYPE C Inherent force limiting.

TYPE B1 and B2 monitored contact and non-

contact sensors.

If you have questions about compatibility of third

party safety devices, please contact GHOST

CONTROLS

technical support for assistance

at ghostcontrols.com/help.

Refer to the monitored photo eye instructions for proper

placement of the sensors. Proper installation of these

sensors is critical to avoid false tripping while gate is in

motion and to reduce potential entrapment.

CAUTION

Extreme caution must be exercised when automatic

gate opener system is in operation, regardless of which

safety systems are installed and in use.

Содержание TDS2





































































Результаты поиска

Содержание TDS2

Отзывы:

Похожие инструкции для TDS2

Бренды по названию

Популярные бренды

Ghost Controls TDS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TDS2

Отзывы:

Похожие инструкции для TDS2

Бренды по названию

Популярные бренды