Ghost Controls TDS2 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 68

background image

34

P U L L - T O - O P E N

© G h o s t C o n t r o l s

®

2 0 2 1

PROGRAMMING THE CLOSED LIMIT: PULL-TO-OPEN

This is the most common installation. The

CLOSED

limit is when the operator is extended and the gate is in the closed position.

IMPORTANT

ONLY THE OPERATOR ARMS’ EXTENDED LIMIT IS ADJUSTABLE AND CAN BE SET WITH THE CONTROL

BOARD. THE ARMS’ RETRACTED POSITION IS FIXED AND IS NOT ELECTRONICALLY ADJUSTABLE.
THE OPEN POSITION IS SET BY HARDWARE MOUNTING ONLY. Please refer to the hardware installation to

make sure the retracted position is properly set/installed.

Installation Type

Retracted Position

Extended Position

Pull-To-Open

Gate at the fully

OPEN

position (not

electronically adjustable)

Gate at the

CLOSED

position (elec-

tronically adjustable)

TURN THE CONTROL BOX ON

STEP 18.

Setting the closed limit for each operator arm

A. Press and hold the 1st set

JOG CLOSE

button on the gate system

control board until the 1st gate reaches the

desired closed position.

The gate can move only if pressure is maintained. Releasing the

JOG

button will stop the gate immediately. Once the 1st set is

programmed then repeat for the 2nd gate with the 2nd set

JOG CLOSE

button.

B. Both

JOG

OPEN

or

JOG CLOSE

buttons are needed to ‘fine-tune’ your

desired CLOSED position.

STEP 19.

Press and hold the 1st set limit button on the control panel until it beeps, then release.

Then Press and hold the 2nd set limit button until it beeps, then release.

STEP 20.

Press the transmitter button to activate the gate and let the gate open fully. You should

hear a single beep.

When the gate reaches its

OPEN position, the control board will sound a single beep, confirming the CLOSED limit has been set.

A. Confirm the newly programmed CLOSED limit by pressing the remote transmitter button to activate the

gate and confirm the closed position has been set correctly. This limit is stored and remembered even when all

of the power sources are removed.

B. Repeat STEPS 18-20 if needed to change your desired CLOSED position.
C. Test your system with the remote transmitter to make sure it opens and closes without errors.

«
...
32
33
34
35
36
...
»

Содержание TDS2





































































Отзывы:

Нет отзывов

Похожие инструкции для TDS2

Бренд: FAAC Страницы: 35

Бренд: FAAC Страницы: 6

Бренд: Daspi Страницы: 12

Бренд: SOMFY Страницы: 2

Бренд: SOMFY Страницы: 32

Бренд: SOMFY Страницы: 72

Бренд: Xtreme Garage Страницы: 2

Бренд: ARCO Страницы: 7

Бренд: V2 Страницы: 92

Бренд: Dea Страницы: 20

Бренд: Reisinger Страницы: 20

Бренд: Daspi Страницы: 12

Бренд: CAME Страницы: 28

Бренд: TdA Страницы: 13

Бренд: Wayne-Dalton Страницы: 40

Silencio OTH-A.06

Бренд: Manaras Страницы: 12

Windload Post 9100

Бренд: Wayne-Dalton Страницы: 9

CribClicker BT385

Бренд: Biketronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды