Ghost Controls TDS2 Скачать руководство пользователя

Страница: 48 / 68

P U S H - T O - O P E N

DIP SWITCH OPTION SETTINGS. There are four DIP Switches located on the main control board (shown) that must be

positioned properly for your particular installation.

A. DIP #1 OPEN DIRECTION. The opening direction of the gate operator is determined by DIP#1.

DIP Switch # OFF Position

ON Position

Pull-To-Open (Factory Default): Gate is

pulled to open into your property.

Push-To-Open Installation: Gate is pushed to open away from

your property.

B. DIP #2 ALARM WARNING. The warning alarm is determined by DIP#2.

DIP Switch # OFF Position

ON Position

Warning Disabled: AUTOCLOSE and

initial gate movement alarm warning is

disabled. This does not disable the alarm

warning for consecutive obstruction as

required by UL325 safety standard.

Warning Enabled (Factory Default): AUTOCLOSE and initial

gate movement warning is enabled.

C. DIP #3 MONITORED SAFETY DEVICES. Keep Switch To The Left (Factory Setting) Unless Using

Monitored External Safety Devices Than Switch To The Right.

YOUR SYSTEM WILL NOT WORK IF SAFTEY MODE IS ON

AND YOU DO NOT HAVE MONITORED EXTERNAL

SAFETY DEVICES CONNECTED.

DIP Switch # OFF Position (FACTORY SETTING) ON Position

Patent-pending

SafeForce® Mode

(Factory Default): Force output

is limited to ensure safe opera-

tion as specified by Type C in UL325

requirement.

Monitored Safety Mode: Monitored safety devices required /

Compatible GHOST CONTROLS

safety devices only.

Monitored safety devices must be present and operate prop-

erly as specified by Type B1 or B2 in UL325 requirement. See

monitored safety device connection in the monitored photo eye

instructions manual for more details.

D. DIP #4 DUAL (BI-PARTING) GATE OPENING SEQUENCE. The gate opening sequence for dual gate

opener systems only is determined by DIP#4.

The SECOND arm will always CLOSE first before the FIRST arm.

DIP Switch # OFF Position (FACTORY SETTING) ON Position

Delay Open (Factory Default): FIRST

arm will open before the SECOND arm.

Simultaneous Open: Both the FIRST arm and the SECOND

arm will simultaneously OPEN.

If Gate Lock is installed,

the system will ignore this DIP switch setting and default to

delay open on the SECOND arm.

Содержание TDS2





































































Результаты поиска

Содержание TDS2

Отзывы:

Похожие инструкции для TDS2

Бренды по названию

Популярные бренды

Ghost Controls TDS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TDS2

Отзывы:

Похожие инструкции для TDS2

Бренды по названию

Популярные бренды