Ghost Controls TDS2 Скачать руководство пользователя страница 58

Страница: 58 / 68

P U S H - T O - O P E N

2 0 2 1

SETTING AUTOCLOSE TIME ON YOUR GATE

The

AUTOCLOSE TIME setting determines how long the gate will remain open each time it operates before automatically

closing. The

factory default setting is off which requires the user to push either a remote transmitter button, keypad code, or

push-button to close the gate.

NOTE

The AUTOCLOSE time period begins once the gate has reached its open limit.

Minimum AUTOCLOSE Time Period

Maximum AUTOCLOSE Time Period

6 Seconds

60 Minutes. If longer time is needed, you should enable

PartyMode or Disable AUTOCLOSE.

A. Press and hold the

SET AUTOCLOSE TIME

button until it beeps.

B. Release the button and start counting the blinks or watching a clock until the desired AUTOCLOSE time has

been reached. (the LED will blink once a second)

C. Press and release the

SET AUTOCLOSE TIME

button. The alarm will sound. AUTOCLOSE time can be

set from 6 seconds to 60 minutes.

D. The AUTOCLOSE feature is now enabled.

Содержание TDS2





































































Результаты поиска

Содержание TDS2

Отзывы:

Похожие инструкции для TDS2

Бренды по названию

Популярные бренды

Ghost Controls TDS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TDS2

Отзывы:

Похожие инструкции для TDS2

Бренды по названию

Популярные бренды