Ghost Controls TDS2 Скачать руководство пользователя страница 65

Страница: 65 / 68

A C C E S S O R I E S

2 0 2 1

UNIVERSAL TUBE GATE BRACKET KIT | AXTB

Mounting bracket kits that will attach a variety of devices to 1-1/2’-2” tubes including tubular gates. These

include gate opener kits, ZombieLock

, or any other device that needs to be attached to tubes.

WIRED VEHICLE SENSOR | AXXV
The GHOST CONTROLS

Vehicle Sensor is the easiest way to trigger your gate to open when a vehicle

is trying to exit your property. This sensor is buried beneath the ground surface next to your driveway and

connects into your gate controller box. 55’ cable included (cannot be spliced)

WIRELESS VEHICLE SENSOR | AXWV
The GHOST CONTROLS

Vehicle Sensor is the easiest way to trigger your gate to open when a vehicle is

trying to exit your property. This sensor is easy to install and sensor is buried beneath the ground surface next

to your driveway and takes 2 C batteries. Does not connect into the control box.

PUSH BUTTON | AXPB
The standard push button will control a single or dual gate system up to 1,000’ ft away with low voltage wire.

LOCKING CLEVIS PIN | AXLC
The GHOST CONTROLS

Locking Clevis Pin allows you to easily secure the gate operator arm to the

mounting brackets with a padlock by replacing the Clevis pin included in the gate opener kit.

100' WIRE | AXLV

100

of 16 AWG low voltage, direct burial, standard wire for wiring the transformer or running the power cable

from solar panel.

PHOTO EYES | AXPS
Adjustable photo eyes for your outdoor environment. We offer monitored and non-monitored versions.

PUSH-TO-OPEN GATE BRACKET KIT | AXPO
The Push-To-Open Bracket is required for any gate opener system that is installed when the installation causes

the gates to swing out from the property. Most gates are installed with the swing action into the property and do

not require these brackets. Dual gates will need (2) AXPO kits.

Содержание TDS2





































































Результаты поиска

Содержание TDS2

Отзывы:

Похожие инструкции для TDS2

Бренды по названию

Популярные бренды

Ghost Controls TDS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TDS2

Отзывы:

Похожие инструкции для TDS2

Бренды по названию

Популярные бренды