manualshive.com logo in svg

GHM GREISINGER GIA 20 EB, Инструкция по монтажу и эксплуатации

Поделиться
Скачать
GHM GREISINGER GIA 20 EB Скачать руководство пользователя страница 30

E31.0.12.6C-06 

Mounting and operating manual GIA 20 EB with electrically insulated supply

 

page 30 of 32 

Err.4: 

Values below display range 

Indicates that display value is below the valid display range of the device (-1999 digit). 

Possible causes: 

- Incorrect scale.  
- Counter underflow. 

Remedies: 

- The error-message will be reset if the display value is above -1999. 
- Reset the counter 
– When happening frequently, check the scale-setting, maybe it was set too
  low and should be increased. 

Err.7: 

System-error 

The device features an integrated self-diagnostic-function which checks essential parts of the de-
vice permanently. When detecting a failure, error-message Err.7 will be displayed. 

Possible causes: 

- Valid operating temperature range has been exceeded or is below  the
   valid temperature range.  
- Device defective. 

Remedies: 

- Stay within valid temperature range. 
- Exchange the defective device. 

Err.9: 

Sensor defective 

The device features an integrated diagnostic-function for the connected sensor or transmitter. 
When detecting a failure, error-message Err.9 will be displayed. 

Possible causes: 

- Sensor broken or sensor shorted (Pt100 or Pt1000). 
- Sensor broken (thermo-elements). 

Remedies: 

- Check sensor or exchange defective sensor. 

Er.11:  Value could not be calculated 

Indicates a measuring value, needed for calculation of the display value, is faulty or out of range. 

Possible causes: 

- Incorrect scale. 

 

 

Remedies: 

- Check settings and input signal

 

13. Decommissioning, reshipment and disposal 

13.1. Decommissioning 

Always disconnect the device before from its supply before decommission (e.g. at fuse). Valid 
general safety requirements shall be observed. 

Please also make sure that connected Loads are disconnected also and are in a safe state.

 

13.2. Reshipment and disposal 

 

All devices returned to the manufacturer have to be free of any residual of measuring 
media and other hazardous substances. 
Measuring residuals at housing or sensor may be a risk for persons or environment 

 

 

 

 

Use an adequate transport package for reshipment, especially for fully functional 
devices. Please make sure that the device is protected in the package by enough 
packing materials. 

Add the completed reshipment form of the GHM website  

http://www.ghm-messtechnik.de/downloads/ghm-formulare.html

. 

 

 

The device must not be disposed in the unsorted municipal waste! Send the device 
directly to us (sufficiently stamped), considering the above if it should be disposed.  
We will dispose the device appropriate and environmentally sound. 

 

 

Содержание GREISINGER GIA 20 EB

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды