manualshive.com logo in svg

GHM GREISINGER GIA 20 EB, Инструкция по монтажу и эксплуатации

Поделиться
Скачать
GHM GREISINGER GIA 20 EB Скачать руководство пользователя страница 24

E31.0.12.6C-06 

Mounting and operating manual GIA 20 EB with electrically insulated supply

 

page 24 of 32 

*

4 

:

  

Low-/High-side-switch: opened in case of an error. Push-Pull-output:  low in case of an error. 

*

5 

:

  

Low-/High-side-switch: closed in case of an error. Push-Pull-output:  high in case of an error  

Finish configuration: 

Press

 Button 1

 as often till the device executes a reset. The values will be stored at it.

 

 

Switching delay:

 

The value for the switching-delay is the time [in sec] the device waits at least to switch on the output 
again after the output was switched off. 

 

8. Offset- and slope-adjustment 

The offset and slope-adjustment function can be used for compensating the tolerance of the used 
sensor, and for venire adjustment of the used transducer or transmitter. 

 

The settings of the offset- / slope-adjustment will be cancelled, when no button was 
pressed for more than 60 sec. Changes you may have made already 

won‘t be saved 

and will be lost!

  

The settings of the offset- / slope-adjustment and alarm-boundaries will automatically 
be reset to factory default when any changes for the settings  “InP”, “SEnS“ or. “Unit“ 
had been made!

 

 

Calling the Menu: 

Press

 Button 3

 >2 Seconds.

 

General description and notes to the operating of the menu:

 

The Display has to show 

0FFS

 ('Offset').

 

With 

Button1 

you can go to the next parameter resp. after the last 

parameter values will be 

saved

. 

With

 Button 2

 or

 Button 3

 you can adjust the value.  

 

 

 
If no key is pressed > 60 sec. the menu will be automatically closed. 

 

 

 

Button 1 Button 2 Button 3 

Содержание GREISINGER GIA 20 EB

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды