manualshive.com logo in svg

GHM GREISINGER GIA 20 EB, Инструкция по монтажу и эксплуатации

Поделиться
Скачать
GHM GREISINGER GIA 20 EB Скачать руководство пользователя страница 21

E31.0.12.6C-06 

Mounting and operating manual GIA 20 EB with electrically insulated supply

 

page 21 of 32 

Finish configuration: 

Press

 Button 1

 as often till the device executes a reset. The values will be stored at it.

 

. 

 

Connection:

 

For the connection of a frequency-transmitter, please follow the instructions given in chapter 5.3.7. 
When connecting a switching-contact-transmitter with increased frequency range (= with external 
circuitry) you have to select TTL as input signal. 

 

Divisor:

 

The incoming pulses will be divided with the selected pre-scaling factor, after that they will be 
transmitted to the device for further processing. By this factor you can adapt the device to your 
transmitter or select a pre-scaling factor for large values.

 

Example: 

Your transmitter emits 1800 pulses per litre and you expect a flow rate of 300 litres. The display 
should be in litre with a resolution of 0.1 litres. 

The pulses to be counted are 1800 Impulses * 300 litres, would result 540000 in Impulses. This 
overrides the upper counter range. By setting the pre-scaling factor of 100 the pulses are reduced 
to 540000/100 = 5400. The upper counting range limit has to be set to 5400. 
 

The display should have a resolution of 0.1 liters. the decimal point position has to be ---.- and a 
display range limit of 300.0. 

 

6.7. Interface mode 

When the device is in the interface mode it won’t make any measurements by itself. The value 
shown in the device’s display is sent via serial interface. But the switching and alarm functions of 
the displayed value are still available. 

The EASYBus-Address of the device needed for the communication can be set manually with the 
device itself or with the help of an EASYBus-software (like Easybus Configurator). Please note, 
when carrying out an EAYBus-system-initiali

sation the device’s address will be reset automatically. 

This chapter describes how to configure the device as an EASYBus-display.  
This instruction demands that you selected “

SEri

“ as input type like it is explained in chapter 6.1.  

In der Anzeige muss 

INP

 stehen.  

Parameter 

Button 1 

Value 

Button 2 / 3  

Notes 

ADR

 

0 ... 239 

Address 

DP

 

"- - - -" 

 "- - - . -" 
 "- - . - -" 

"- . - - -" 

Decimal point 

O

 V

TP 

 

Output configuration will be explained in chapter 7. According to 
your settings different parameters will be shown. 

Finish configuration: 

Press

 Button 1

 as often till the device executes a reset. The values will be stored at it.

 

.

 

 

 

 

 

Содержание GREISINGER GIA 20 EB

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды