GHM GREISINGER GIA 20 EB Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 32

GHM GREISINGER GIA 20 EB Скачать руководство пользователя страница 20

E31.0.12.6C-06

Mounting and operating manual GIA 20 EB with electrically insulated supply

page 20 of 32

6.6. Up-/Downwards counter (TTL, switching-contact)

The upwards counter starts counting upwards from 0 according to its settings. The downwards
counter starts counting downwards from the upper value that had been selected.

The current value of the counter can be reset anytime by connecting pin 8 to GND (e.g. pin 7).
The counter starts from its beginning as you disconnect pin 8 and pin 7.

Feature:

The present counter value won‘t be lost if the voltage supply is disconnected. The counter

starts from this value after restarting.

This chapter describes how to configure the device as a counter.

This instruction demands that you selected “

Co.up

“ or “

Co.dn

“ as input type like it is explained in

chapter 6.1.

The display must show

INP

.

Parameter

Button 1

Value

Button 2 / 3

Notes

SENS

TTL

TTL-signal

NPN

Switching contact, NPN
For direct connection of a passive switching contact (e.g. push
button, relay) or transmitter with NPN output.
There is a internal pull-up-resistor.

PNP

Switching contact, PNP
For direct connection of a transmitter with PNP output.
There is a internal pull-down-resistor.

EDGE

POS

The counter is triggered on the positive (rising) edge.

NEG

The counter is triggered on the negative (falling) edge.

D,V

1 ... 1000

divisor (see info divisor)

(O.K,

0 ... 9999

Upper counting range limit
The lower counter-range-limit (downwards counter) is fixed with 0.

DP

"- - - -"

"- - - . -"
"- - . - -"

"- . - - -"

Decimal point

D,.K,

-1999 ... 9999

Upper counting range limit

L ,

(Limit)

OFF

Exceeding of the counter range is tolerable until you reach the
maximum measuring range limit.

ON.ER

The measuring range is exactly bounded by the selected counter-
range-limit. When exceeding or short falling of the limit the device
will display an error message.

ON.RG

The measuring range is exactly bounded by the selected counter-
range-limit. When exceeding or short falling of the limit the device
will display the upper counter-range-limit or 0.

O

V

TP

Output configuration will be explained in chapter 7. According to
your settings different parameters will be shown.

«
...
18
19
20
21
22
...
»

Содержание GREISINGER GIA 20 EB

































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды