Genie GCL-J&H Скачать руководство пользователя страница 36

Страница: 36 / 56

8.2

OPEN

STOP

CAL

RUN

SCROLL

SET

CLEAR

OPEN

STOP

CAL

RUN

SCROLL

SET

CLEAR

Operators also include a run code memory that stores the last 10 run events.

These codes are stored with or without power. Each time the operator runs or stops, it

generates a code that it stores in this memory (Why the operator ran or stopped). Used

together with the error code memory, it becomes a powerful troubleshooting aid.
The run code memory stores the last 10 codes in sequence. Once 10 codes are stored,

the oldest code is erased to make room for the newest code. These codes are displayed

in calibration mode. The display will flash the number of the run code and the 2-digit

run code followed by a description of the run code.

Fig. 3 & 4

Run Codes

RUN CODE 1 3C

Figure 3

HALT DOWN LIMIT

Figure 4

Error Codes

(continued)

CAL

RUN

SCROLL

SET

CLEAR

CAL

RUN

To view the error code memory

1) Press CAL/RUN key to enter calibration mode.

2) Press SCROLL key until display reads “ERROR CODE 1

”.

•

The display will begin flashing the error code number and 2-digit

error code followed by its description.

•

Reminder: Error code number 1 is the latest code generated.

3) Press SET/CLEAR key. The display will now read “ERROR CODE 2

.”

(This is the error code which was generated before error code 1.)

4) Repeat step 3 until all 10 error codes have been displayed or move on to

step 5 when ready.

5) Press CAL/RUN key to return to run mode.

NOTE

: For all error codes see Appendix C, Pages 10.11 - 10.12.

www.geniecompany.com

-12

Standard Duty Operator

GCL-J&H

Содержание GCL-J&H

























































Результаты поиска

Содержание GCL-J&H

Отзывы:

Бренды по названию

Популярные бренды

Genie GCL-J&H, Руководство по установке

Результаты поиска

Содержание GCL-J&H

Отзывы:

Бренды по названию

Популярные бренды