Genie GCL-J&H Скачать руководство пользователя страница 27

Страница: 27 / 56

6.4

OPEN

STOP

CAL

RUN

SCROLL

SET

CLEAR

Setting Travel Limits

UP LIMIT CLR

Figure 7

OPEN

STOP

CAL

RUN

SCROLL

SET

CLEAR

DOWN LIMIT SET

Figure 8

CAL

RUN

SCROLL

SET

CLEAR

OPEN

SCROLL

CAL

RUN

Resetting Travel Limits

CAL

RUN

CROL

OPEN

SET

CLEAR

CAL

RUN

SET

CLEAR

UP and/or DOWN

1) If operator is in RUN mode, press CAL/RUN key to enter calibration mode.

2) Press SCROLL key until display reads “UP LIMIT>CLR ” or

“DOWN LIMIT>CLR ”

Figure 7

3) Jog the door using the OPEN or CLOSE key until you reach the

desired height.

4) Press SET/CLEAR key to switch display to “UP LIMIT>SET “ or

“DOWN LIMIT>SET .“

Figure 8

5) Press a SCROLL key to shift to a new function and lock in the

limit setting.

6) Press CAL/RUN key to return to run mode.

UP and/or DOWN

1) If operator is in RUN mode, press CAL/RUN key to enter calibration mode.

2) Press SCROLL key until display reads “UP LIMIT>SET ” or

“DOWN LIMIT>SET.”

Figure 8

3) Press SET/CLEAR key to switch display to ”UP LIMIT>CLR” or

”DOWN LIMIT>CLR”

4) Jog the door using the OPEN or CLOSE key until you reach the

desired height.

5) Press SET/CLEAR key to switch display to ”UP LIMIT>SET” or

”DOWN LIMIT>SET”

6) Press CAL/RUN key to return to run mode.

www.geniecompany.com

08-12

Standard Duty Operator

GCL-J&H

NOTE

: The recommended setpoint for the DOWN Travel Limit is normally at

approximately 2 inches off the floor. This final distance will be covered by the Limit

Overrun Function to establish a more accurate seal.

Содержание GCL-J&H

























































Результаты поиска

Содержание GCL-J&H

Отзывы:

Бренды по названию

Популярные бренды

Genie GCL-J&H, Руководство по установке

Результаты поиска

Содержание GCL-J&H

Отзывы:

Бренды по названию

Популярные бренды