Genie GCL-J&H Скачать руководство пользователя страница 30

Страница: 30 / 56

6.7

OPEN

STOP

CAL

RUN

SCROLL

SET

CLEAR

OPEN

1) If operator is in RUN mode, press CAL/RUN key to enter calibration mode.

2) Press SCROLL key until display reads “OPEN MODE>MOM” or

“OPEN MODE>C-STP.”

Figure 11

MOM=momentary contact, meaning you

press and release

the

OPEN

key and

the door will continue to move

until

it reaches

its travel limit. (See NOTE)

C-STP=constant contact-stop, meaning

if you release the key

prior

to the door reaching its travel limit,

the door will stop

3) Press SET/CLEAR key to toggle between “OPEN MODE>C-STP” or

“OPEN MODE>MOM” on the display.

4) Press a SCROLL key to shift to a new function and lock in the setting.

5) Press CAL/RUN key to return to run mode.

CLOSE

1) If operator is in RUN mode, press CAL/RUN key to enter calibration mode.

2) Press SCROLL key until display reads “CLOSE MODE>MOM,”

“CLOSE MODE>C-STP” or “CLOSE MODE>C-REV.”

Figure 12

MOM=momentary contact, meaning you

press and release

the

CLOSE key and

the door will continue to move

until it reaches

its travel limit. (See NOTE)

C-STP=constant contact-stop, meaning

if you release the key

prior

to the door reaching its travel limit,

the door will stop

C-REV=constant contact-reverse, meaning

if you release the key

prior to the door reaching its travel limit,

the door will

reverse direction

. (See NOTE)

3) Press SET/CLEAR key to toggle between “CLOSE MODE>C-STP” or

“CLOSE MODE>C-REV” or ”CLOSE MODE>MOM” on the display.

4) Press a SCROLL key to shift to a new function and lock in the setting.

5) Press CAL/RUN key to return to run mode.

Setting Open and Close Modes

(Constant vs Momentary Contact)

OPEN MODE MOM

Figure 11

OPEN

STOP

CAL

RUN

SCROLL

SET

CLEAR

CLOSE MODE C-STP

Figure 12

NOTE

: Momentary contact

(MOM)

or Constant Reverse (

C-REV

) may not be used

unless both the OPEN and CLOSE Limits have been set.
In situations where an external reversing device is either not installed or not

operating properly, Constant Contact

(C-STP)

MUST BE USED.

NOTE

: During adjustment of a Travel Limit, the Open and Close Modes will

automatically fail-safe to Constant Contact until the Limit has been set or reset.

At that time the Open and Close Modes will revert to their previous setting.

CAL

RUN

S O L

SCROLL

C EA

OPEN

SET

CLEAR

SCROLL

LOSE

CAL

RUN

SC L

CLEA

LO E

CAL

RUN

ROLL

C L

SCROLL

L AR

SET

CLEAR

SCROLL

CAL

RUN

WARNING:

If momentary contact control is to be used, an external

reversing device such as a photocell system or sensing edge switch must be

used. See pages 5.7-5.8 for installation of entrapment protection devices.

www.geniecompany.com

-12

Standard Duty Operator

GCL-J&H

Содержание GCL-J&H

























































Результаты поиска

Содержание GCL-J&H

Отзывы:

Бренды по названию

Популярные бренды

Genie GCL-J&H, Руководство по установке

Результаты поиска

Содержание GCL-J&H

Отзывы:

Бренды по названию

Популярные бренды