Genie GCL-J&H Скачать руководство пользователя страница 32

Страница: 32 / 56

OPEN

STOP

CAL

RUN

SCROLL

SET

CLEAR

Setting Mid-Stop Limit

Figure 16

CAL

RUN

CROLL

OPEN

CAL

RUN

CAL

RUN

SET

CLEAR

SCROLL

The Operator includes a programmable Mid-Stop. This feature allows the operator

to stop at a user selectable point when opening. It is used when operating very tall doors

that only open to their full height occasionally. The Mid-Stop does not effect the operator

when closing. To operate door to full open position from mid-stop, press open button again.

NOTE

: Setting of the MID-STOP should only be performed AFTER Travel

Limit and Max Run Timer settings have been made.

1) Press CAL/RUN key to enter calibration mode.

2) Press the CLOSE key to close the door to the down limit.

3) Press SCROLL

key until display reads “MID-STOP

CLR”

Figure 16

NOTE

: If the display reads MID-STOP

SET at this point, first clear the

MID-STOP as described below then repeat steps 1-3 and continue.

4) Press the OPEN

key to open the door to desired mid-stop height.

5) Press SET/CLEAR keyuntil the display reads ”MID-STOP

SET”

6) Press CAL/RUN key to return to run mode.

To CLEAR the Limit

1) Press CAL/RUN to enter calibration mode.
3) Press SCROLL until display reads “MID-STOP

SET”

5) Press SET/CLEAR until the display reads ”MID-STOP

CLR”

8) Press CAL/RUN to return to run mode.

OPEN

STOP

CAL

RUN

SCROLL

SET

CLEAR

MAX RUN TMR SET

Figure 17

CAUTION:

The MID-STOP feature must be turned off in

order to properly set the Max Run Timer.

SET

CLEAR

TO RESET

1) Press CAL/RUN to enter calibration mode.

2) Press SCROLL (up or down) until display reads

”MAX RUN TMR > SET.”

Figure 17

3)   Press SET/CLEAR until display reads ”MAX RUN TMR > CLR.”
4)   Press CAL/RUN to return to RUN mode.
5)   Cycle the door between limits.

NOTE

The Max Run Timer must be reset each and every time the Travel Limits are adjusted.

Resetting the MRT

(The Max Run Timer is set automatically once the unit is cycled between

Limits. The Max Run Timer prevents the unit from running continuously in the event of a problem.

The MRT’s are set to the time required to run from one limit to the other, plus 5 seconds (nominal).

When the MRT is exceeded, the operator stops and will not respond to any command until it is reset

by pressing one of the Calibration keys or by cycling power to the unit.

CAL

RUN

SET

CLEAR

CAL

RUN

SCROLL

www.geniecompany.com

-12

Standard Duty Operator

GCL-J&H

CAL

RUN

MID-STOP CLR

Содержание GCL-J&H

























































Результаты поиска

Содержание GCL-J&H

Отзывы:

Бренды по названию

Популярные бренды

Genie GCL-J&H, Руководство по установке

Результаты поиска

Содержание GCL-J&H

Отзывы:

Бренды по названию

Популярные бренды