Genie GCL-J&H Скачать руководство пользователя страница 12

Страница: 12 / 56

4.5

www.geniecompany.com

-12

Standard Duty Operator

GCL-J&H

1) Route the hand chain through the chain guide, around the

pocket wheel and back through the chain guide.

Fig.5

2) Connect the hand chain ends together as shown in

Fig 6

by twisting open the last link on one end of the chain, and

slipping the last link on the opposite end onto the open link.

3) Twist open link closed again.

4) Mount chain keeper to wall in line with chain approximately

4 feet from floor.

5) Loop chain around keeper as shown.

Fig. 7

. Optional Padlock

not provided.

6) Install hoist cable.

•

With operator installed motor DOWN, attach hoist cable to

cam arm hole closest to mounting plate.

Fig. 8

•

With operator installed motor UP, attach hoist cable to cam

arm hole closest to electric box.

Fig. 8

Hand Chain and Keeper

Figure 6

Figure 7

NOTE

: To insure smooth operation, make sure there is no twist in the

hand chain before connecting the link ends together.

MOUNTED

MOTOR UP

MOUNTED

MOTOR DOWN

ATTACH

HOIST

CABLE

HERE

Figure 8

ATTACH

HOIST

CABLE

HERE

Figure 5

Содержание GCL-J&H

























































Результаты поиска

Содержание GCL-J&H

Отзывы:

Бренды по названию

Популярные бренды

Genie GCL-J&H, Руководство по установке

Результаты поиска

Содержание GCL-J&H

Отзывы:

Бренды по названию

Популярные бренды