General DataComm 060A027-001 Скачать руководство пользователя | Manualshive

Страница: 126 / 138

background image

Tests

Analog Loopback (ANALOOP)

6-2

SpectraComm Dual V.34 Modem

060R122-000

Installation and Operation

Issue 15

Analog Loopback (ANALOOP)

The Analog Loopback (AL) test mode, illustrated in

, is provided to isolate problems in

the data set operation and the DTE interface. Specifically, AL tests modem modulator/demodulator
operation, DTE receive/transmit operation, and DTE interface operation. This test can be
controlled from the front panel or by AT commands. It can also be commanded by an SNMP
controller, such as the TEAM MMS (

Modem Management System)

.

Note

When the modem is used in

\N0

,

\N2

,

\N3

,

\N4

or

\N5

modes with a fixed DTE speed, it will not issue

a CONNECT message. When the modem is used in

\N1

mode, since the AL handshake speed may not

match the DTE speed selected, the modem issues a CONNECT _ _ _ _ message at the last known DTE
rate. If the DTE rate and handshake rate differ, the user can change the DTE speed to match the rate
reported by the CONNECT message.

Table 6-1

Local Test

Step

Front Panel

AT Command Mode

1.

To start the test, press AL for modem you are testing
(a or b).

To start the test, type:

AT&T1

(enter). If modem

responds with an error message, type:

AT&T0

(enter), which resets the test mode, then re-enter
the command.

2.

The TM LED flashes while the modem is setting up the test, then lights while the test is running.

3.

Enter test data at the DTE. Compare the data that was entered at the DTE with the data that is looped
back and displayed by the DTE. If errors occur frequently, a problem may exist in the modem, the DTE,
or the DTE-to-modem connection.

For fault isolation refer to

.

4.

To end the test, press AL switch again.

To end the test, type the escape sequence (

+++

)

and, after the modem is in the command mode,
type:

AT&T0

(enter).

«
...
124
125
126
127
128
...
»

Содержание 060A027-001











































































































































Отзывы:

Нет отзывов

Похожие инструкции для 060A027-001

Бренд: Ovation Страницы: 19

Бренд: BROSTREND Страницы: 13

Бренд: Yifan Страницы: 6

Бренд: Yifan Страницы: 33

Бренд: Yifan Страницы: 35

Бренд: PROLiNK Страницы: 10

USB ADSL Modem Hurricane Series

Бренд: PROLiNK Страницы: 21

Бренд: Spytec Страницы: 12

Бренд: NETGEAR Страницы: 175

Бренд: FRITZ!WLAN Страницы: 6

Бренд: FRITZ!WLAN Страницы: 6

Бренд: ADB Страницы: 104

Бренд: Zte Страницы: 9

Бренд: RACOM Страницы: 34

715 P/N - 13H6715

Бренд: IBM Страницы: 47

Бренд: Radyne Страницы: 214

Бренд: Maxis Страницы: 63

Бренд: Arris Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды