General DataComm 060A027-001 Скачать руководство пользователя | Manualshive

Страница: 49 / 138

background image

Operation

Security Overview

060R122-000

SpectraComm

Dual V.34 Modem

3-15

Issue 15

Installation and Operation

AES Encryption Security

A modem purchased from the factory with AES Encryption is already capable of encryption.
Modems in the field can be returned to the factory for an encryption upgrade. For modems already
installed in a customer’s network, contact your service representative to arrange for an upgrade. A
modem is capable of AES Encryption when the following conditions are met:

•

Both modems must be at Firmware Version 8.3.0.0 or higher.

•

Both modems must be enabled from the factory for AES Encryption.

•

There must be a V.42 or V.42bis link.

•

Both modems must be configured for encryption via expanded AT commands entered at
the modem rear panel terminal port, the SCM craft port or via a Telnet connection.
The sequence of configuration commands is provided below.

AES Encryption Configuration Procedures

1. Access the modem AT command set from the desired management interface. If using the

SCM, ensure that Switch S1-4 on the SCM card is set to the

Open

position. This is the

factory default which allows the terminal to function with the SCM card.

2. Enter the following AT command:

AT&F

3. Configure the modem with the Encryption Key using the following AT command. Encryption

key must be entered in both modems exactly with no errors, spaces, corrections or backspaces.

AT%X1=

[Encryption Key]

where the key consists of up to 32 ASCII characters (no commas)

4. Configure a security solution by entering one of the following AT commands:

AT%S8

sets the modem for AES Encryption only

AT%S9

sets the modem for SteadFast Security and AES Encryption

AT%S11

sets the modem for SteadFast Security, AES Encryption and RADIUS Authentication

5. Select encryption key size:

AT)M

n

where n is 0, 1 or 2 (0 = 128 bits, 1 = 192 bits, 2 =256 bits)

6. Select encryption mode:

AT@M

n

where n is 0, 1 or 2 (0 = ECB, 1 = CBC, 2 = CTR)

7. Set the asynchronous protocol to V.42 Only by typing:

AT\N4

If V.42bis compression is desired, type

AT%C1

in addition.

8. Display the AES Encryption key by typing:

AT%W

9. Check that the modem shows the presence of AES Encryption by typing

ATI4

.

(The Product Type field will display

EC

when AES Encryption is operational.)

10. Repeat this procedure in its entirety for the modem on the opposite end of the link.

Note

Enter up to16 characters to yield a 128-bit encryption key; enter 24 characters to yield a 192-bit encryp-
tion key; enter 32 characters to yield a 256-bit encryption key.

Note

Setting the

%S8

,

%S9

or

%S11

commands will flash the DTR LED when the modem is in data mode.

These commands will also affect the connect message by adding

AES

to the end of the protocol string.

«
...
47
48
49
50
51
...
»

Содержание 060A027-001











































































































































Отзывы:

Нет отзывов

Похожие инструкции для 060A027-001

Бренд: SCS Страницы: 217

Бренд: Best Data Products Страницы: 41

Spartan 57076-1

Бренд: Traxxas Страницы: 30

Бренд: SafeNet Страницы: 54

Бренд: Data-Linc Group Страницы: 31

Бренд: StarHub Страницы: 10

Бренд: Paradyne Страницы: 3

Бренд: Swegon Страницы: 4

Бренд: ICPDAS Страницы: 8

Бренд: B+B SmartWorx Страницы: 2

Бренд: Atech Tech Страницы: 42

Бренд: 3onedata Страницы: 5

Бренд: Terayon Страницы: 20

Бренд: HSP Страницы: 8

Бренд: 3One data Страницы: 11

Бренд: Telfort Страницы: 10

Бренд: RACOM Страницы: 248

Бренд: ICP DAS USA Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды