manualshive.com logo in svg

General DataComm 060A027-001, Руководство по установке и эксплуатации

Поделиться
Скачать
General DataComm 060A027-001 Скачать руководство пользователя страница 92

AT Command Set Operation

AT Command Reference Tables

4-12

SpectraComm Dual V.34 Modem

060R122-000

Installation and Operation

Issue 15

O

n

On-line

Instructs the modem to go on-line (enter data mode) after an escape to local 
command mode is issued. This command transfers the modem from command mode 
to data mode.

O0

Instructs the modem to go on-line.

O1

Instructs the modem to go on-line and issue a retrain sequence if operating in V.34, 
V.22 bis, V32, or V32 bis modes.

%O

n

Answer mode

For a modem on a switched network this command selects the band the modem will 
use for both automatically and manually answered calls. For a modem on a private 
line, this command selects the band the modem will use for connections.

%O0

Commands the modem, in switched network mode, to use the presence of a ring to 
determine the band, regardless if automatic answer is selected. In private line mode, 
the modem will be in the originate band.

%O1

Commands the modem to answer calls in the answer band in either switched network 
or private line mode.

%O2

Commands the modem to answer calls in the originate band in either switched 
network or private line mode.

P

Dialing type

Instructs the modem to use pulse dialing. The command may be used alone or as 
part of a dial string. When

 P 

is used alone, it makes pulse dialing the modem's 

default dialing method. When

 P 

is used in a dial string, it acts as a modifier and 

affects only the dialing of that string. Pulse dialing is blocked by some country code 
configurations.

&P

n

Private line handshake 
mode

Controls the selection of the private line handshake mode.

&P0

Selects V.34 only (28.8 - 2400)

&P1

Selects V.32 bis only (14.4 - 4800)

&P2

Selects V.32 only (9600 and 4800)

&P3

Selects IUT-T 212 (1200)

&P4

Selects IUT-T 103 (300)

%P

n

=

nnn

Store password

Stores passwords in the modem’s 10 memory cells, where 

n 

= 0 - 9 and 

nnn

 = a 

password of up to 10 characters. To disable or clear a cell password, type

 %P

n

=

 

<cr>

. This command is not affected by factory defaults.

%P0=

nnn

When configured for SteadFast Security, cell 0 must be used for the SteadFast 
password.

\P

n

Parity type

Sets up what parity to use in data mode for front ends that do not send AT 
commands.

\P0

Even parity

\P1

Space parity

\P2

Odd parity

\P3

Mark parity

\P4

Automatic parity; last AT (default)

:P

n

Switched network 
transmit type

Selects permissive or programmable mode for switched network operation.

:P0

Selects permissive mode.

:P1

Selects programmable mode.

*P

n

Remote configuration 
security password

Defines the remote configuration security password, where n = a password of 1 to 11 
characters. To disable or clear the password, enter

 *P

.

Содержание 060A027-001











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды