manualshive.com logo in svg

General DataComm 060A027-001, Руководство по установке и эксплуатации

Поделиться
Скачать
General DataComm 060A027-001 Скачать руководство пользователя страница 114

V.25 bis Command Set Operation

Commanding the Modem

5-4

SpectraComm Dual V.34 Modem

060R122-000

Installation and Operation

Issue 15

V.25 

bis Configuration Commands

Configuration commands allow you to configure the modem. 

NVW 

Write Option Settings to User Configuration Profile

NVW saves the current settings to a user configuration profile in the modem's non-volatile memory, 
with the exception of the Terminator Character option (which is set to its factory default, the line 
feed control-character). This command saves a set of option values that is activated when the 
modem is powered up. 

To invoke this command, type:

NVW ; 

n

 <LF>

where n is the user configuration profile (0 to 3). 

PRN

Store Phone Number to Cell

PRN stores a telephone number in one of the modem's ten memory cells.  Numbers stored by means 
of this command can be automatically dialed either by invoking the CRS command in 108.2 mode, 
or by turning On circuit 108.1 in 108.1 mode (108.1 dialing uses only the number stored in memory 
cell 0). 

To store a number, type:

PRN n1 ; n2 <LF>

where n1 is the memory cell (from 0 to 9) in which the number is to be stored, and n2 is the phone 
number to be stored.  n2 may contain any legal dialing characters (0-9 A-D P T # * , < ! & @).  

PRS AA

Automatic Answering

PRS AA controls the automatic answering function.  When you enable automatic answering, you 
can specify the number of rings the modem will wait before it performs automatic answering.  
Default is 4 rings.  

To enable automatic answering, type:

PRS AA ; 

n

 <LF>

where n is the number of rings (from 1 to 255) that the modem waits before automatically answering 
an incoming call.  

To disable automatic answering, type:

PRS AA ; 0 <LF>

PRS AT

AT Command Set

PRS AT switches the modem from V.25 bis command set mode to AT command set mode.  

Table 5-3

Explanation of Invalid Responses

Command Invoked

Description of INV Response

DIC

INC not received.

PRS

Non-selectable option in user's country.

Содержание 060A027-001











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды