General DataComm 060A027-001 Скачать руководство пользователя | Manualshive

Страница: 48 / 138

background image

Operation

Security Overview

3-14

SpectraComm Dual V.34 Modem

060R122-000

Installation and Operation

Issue 15

RADIUS Security (Remote Authentication Dial-In User Service)

When optioned at the factory, the modem can support RADIUS (Remote Authentication Dial-In
User Service). RADIUS is an optional software feature for the SpectraComm Manager Card that
allows a modem optioned for RADIUS to open a client service session for RADIUS security. The
modem can be optioned for RADIUS Security at the time of sale, or at a later time through a factory
upgrade.

When RADIUS is enabled in the modem and the SCM, the modem prompts the caller for a
RADIUS user name and a RADIUS password. This information is passed to the secure RADIUS
server via the SCM for authentication. Once authenticated by the RADIUS server, access to the
network is then either granted or denied.

Confirming RADIUS Capability

To confirm that a particular GDC V.34 modem is capable of RADIUS Security, use the AT
command

I4

and check the Product Code field. If the modem is RADIUS capable the screen will

display the following Product option:

Product Code: SEC

Product code

SEC

indicates that the modem is capable of RADIUS Security. If other Product

codes are displayed, such as

288

, your modem will not support RADIUS.

Enabling RADIUS in the Modem

To enable RADIUS at the answering modem, type in the

%S2

command. Save the configuration

by typing

AT &W

and then press

Enter

. This instructs the modem to perform a RADIUS Security

sequence on every dial-in caller.

Special Considerations

To achieve the highest level of RADIUS Security, perform the following additional steps:

•

Remove all cell passwords from the modem using the

%P

command. This done, if it should

happen that all RADIUS servers fail or if the SCM fails, Online Security will not be forced on
and all dial-in access to the network will be denied until the servers are back online.

•

Disable the capacity for Remote Configuration of the modem by using the

AT *R1

command.

Save this configuration by typing

AT &W

and then press

Enter

.

Note

For detailed information on RADIUS including setup, configuration and operation procedures, refer to
the SpectraComm Manager Card (SCM) Manual, Appendix B: SCM with RADIUS.

Note

To upgrade your modem to RADIUS capability, ask your GDC Sales Representative for that modem’s
RADIUS Feature upgrade (GDC P/N 060U500-D04).

Note

For more information on RADIUS Security, refer to the SpectraComm Manager Card Operation Manual,
Appendix B.

«
...
46
47
48
49
50
...
»

Содержание 060A027-001











































































































































Отзывы:

Нет отзывов

Похожие инструкции для 060A027-001

Бренд: Black Box Страницы: 2

Бренд: Abocom Страницы: 14

LinkWiser-S400M

Бренд: Cellution Страницы: 17

Бренд: MOVITEL Страницы: 28

819-1XRT SERIES

Бренд: Cal Amp Страницы: 48

Бренд: Paradyne Страницы: 85

Бренд: Vega Страницы: 27

Бренд: Moxa Technologies Страницы: 4

Бренд: Quectel Страницы: 36

Бренд: Adeunis RF Страницы: 130

Бренд: NETGEAR Страницы: 2

Бренд: NETGEAR Страницы: 2

5G WI-FI PRO MU500

Бренд: Telstra Страницы: 26

Бренд: PROLiNK Страницы: 14

Бренд: ICPDAS Страницы: 6

Бренд: RCA Страницы: 23

Бренд: SmartRG Страницы: 63

Бренд: adaptiveRF Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды