Gefen EXT-UHD600A-88 Скачать руководство пользователя страница 206

Страница: 206 / 232

page | 194

anc

ed Oper

ation

Commands

#set_showme

Enables or disables the “Show Me” feature. If the “Show Me” feature is enabled,

then all the buttons (with the exception of the Power button), will flash slowly.

This feature allows the matrix to be visually identified on the network and is useful

when multiple matrix units are being used. The default setting is

disabled

Syntax

#set_showme state

Parameters

state

Type:

INTEGER

Accepts a number from the table below, corresponding to the desired state.

state

Description

Disable “Show Me”

Enable “Show Me”

Example

#set_showme 1

SET_SHOWME 1

Related Commands

#get_discovery

#set_discovery

anc

ed Oper

ation

Содержание EXT-UHD600A-88









































































































































































































































Результаты поиска

Содержание EXT-UHD600A-88

Отзывы:

Бренды по названию

Популярные бренды

Gefen EXT-UHD600A-88, Руководство пользователя

Результаты поиска

Содержание EXT-UHD600A-88

Отзывы:

Бренды по названию

Популярные бренды