Gefen EXT-UHD600A-88 Скачать руководство пользователя страница 186

Страница: 186 / 232

page | 174

anc

ed Oper

ation

Commands

#set_discovery_mode

Sets the “discovery” mode. This mode is set to

read/write

by default.

Syntax

#set_discovery_mode

mode

Parameters

mode

Type:

INTEGER

Accepts a number from the table below, specifying the desired state:

mode

Description

Read-only mode

Read / write mode

When set to

read-only

mode, the IP settings for the matrix will be displayed

within the Gefen Syner-G Software Suite but cannot be changed. In order to

both display and allow changes to the IP settings within Gefen Syner-G,

set this feature to

read/write

mode.

Example

#set_discovery_mode 0

DISCOVERY MODE 0

Related Commands

#get_discovery

#get_discovery_mode

#set_discovery

anc

ed Oper

ation

Содержание EXT-UHD600A-88









































































































































































































































Результаты поиска

Содержание EXT-UHD600A-88

Отзывы:

Бренды по названию

Популярные бренды

Gefen EXT-UHD600A-88, Руководство пользователя

Результаты поиска

Содержание EXT-UHD600A-88

Отзывы:

Бренды по названию

Популярные бренды