Gefen EXT-UHD600A-88 Скачать руководство пользователя страница 185

Страница: 185 / 232

page | 173

anc

ed Oper

ation

Commands

#set_discovery

Enables or disables the “discovery” feature. This feature is

enabled

by default.

Syntax

#set_discovery state

Parameters

state

Type:

INTEGER

Accepts a number from the table below, specifying the desired state:

state

Description

Disables “Discovery” mode

Enables “Discovery” mode

If set to

disabled

, then the Syner-G Software Suite will be unable to detect the

matrix on a network. It is recommended that this feature is

enabled

, until the

matrix has been configured for use on a network.

Example

#set_discovery 0

DISCOVERY 0

Related Commands

#get_discovery

#get_discovery_mode

#set_discovery_mode

Содержание EXT-UHD600A-88









































































































































































































































Результаты поиска

Содержание EXT-UHD600A-88

Отзывы:

Бренды по названию

Популярные бренды

Gefen EXT-UHD600A-88, Руководство пользователя

Результаты поиска

Содержание EXT-UHD600A-88

Отзывы:

Бренды по названию

Популярные бренды