GE WSXH208T Скачать руководство пользователя страница 38

Страница: 38 / 51

remove bellows style hose from tub.

10. Remove wire spring clamp from air bell.

11. Remove air shock upper securement pins by de-

pressing locking tab while pulling pin to remove.

This procedure is much easier if a deep 1/2", 6 point

socket (or 13 millimeter, 6 point) is used to com-

press the locking tab of the plastic pin. Push the

socket onto the tapered end of the pin as far as it

will go to compress the locking tab. Use pliers to

grasp head of pin and pull to remove. As the pin is

removed the socket will drop free.

12. Pull upper end of air shocks free from tub and

position shocks upright away from tub for clear-

ance.

13. Protect floor and carefully lay washer on its back.

14. Remove fill spout mounting screws from front

panel.

15. Pull outer lip of bellows from flange on front panel.

16. Remove one screw of the suspension spring retain-

ing strap and loosen the other one. Pivot strap out

of the way to permit access to spring. Remove

suspension springs from washer cabinet and then

from outer tub.

NOTE:

Green end of spring con-

nects to cabinet.

17. Carefully lift cabinet to clear tub assembly and set

aside. Automatic dispenser will remain connected

to tub assembly.

18. Reverse procedure to reassemble.

INNER TUB AND BEARINGS

To Remove or Replace Inner Tub or Bearings:

1. Remove outer tub assembly. See "To Remove or

Replace Outer or Inner Tub" under "OUTER TUB"

section and complete steps 1 - 23.

2. Remove the screws (23) securing the outer tub halves

together. Rotate tub assembly so that front opening

is face down.

3. Remove belt by turning tub drive pulley and rolling

belt off pulley. The belt is elastic and is designed to

"give" enough to remove and install in this manner.

4. Remove pulley from tub shaft.

5. Remove rear motor mounting screws.

6. Separate outer tub halves.

CAUTION:

Use caution

in handling the inner tub, the outer surface is very

sharp! The replacement rear outer tub comes with

new bearings, water seal, and seal between halves

already installed.

7. Remove the inner tub from the tub support by

removing the bolts (6) securing the three legs.

When reassembling, torque bolts to 24 ft. lbs.

8. Reverse procedure to reassemble using illustration

below to show outer tub screw tightening sequence.

After these four, any sequence OK. Torque to 75 -

85 in. lbs.

TUB VANES

Содержание WSXH208T




















































Результаты поиска

Содержание WSXH208T

Отзывы:

GE WSXH208T, Техническое обслуживание руководство, Страница: 38 / 51

Результаты поиска

Содержание WSXH208T

Отзывы: