GE WSXH208T Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 51

GE WSXH208T Скачать руководство пользователя страница 26

25

2. If dryer is stacked on washer, remove clothes dryer

from top of washer.

3. If freestanding or undercounter installation, remove

the top panel.

4. Remove timer knob assembly by pushing in while

turning counterclockwise (CCW) to unscrew.

5. Use pliers to squeeze timer indicator locking tabs

simultaneously, while pulling outward to remove.

NOTE:

Small teeth on timer indicator are used to

adjust indicator dot if cycle does not correspond

with indicated function.

6. Turn timer mounted dispensing cam clockwise

(CW) to position rectangular holes at the 3 o'clock

and the 9 o'clock position, over timer mounting

screws and remove screws.

7. Slide timer rearward to remove (dispensing cam

does not have to be removed). Disconnect timer

terminal blocks to free timer. Note that timer and

terminal blocks are color coded and keyed (to slot

in timer) to ensure correct placement.

8. Install new timer, noting timer shaft and indicator

are keyed to assure correct orientation.

NOTE

: Ensure wiring to new timer is correct before

applying power and testing. Timer has AC and

DC connections. Timer terminal blocks and timer

are color coded to indicate correct positioning.

Refer to appropriate electrical diagram if neces-

sary.

9. Reverse procedure to reassemble.

WATER LEVEL CONTROL

The water level control is a pressure activated single-

«
...
24
25
26
27
28
...
»

Содержание WSXH208T




















































Отзывы:

Нет отзывов