GE WSXH208T Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 51

GE WSXH208T Скачать руководство пользователя страница 31

30

panel front mounting brackets.

4. Remove screws (6) securing the control panel. Five

of the screws are located on the rear of the control

panel and one screw is on the front side, located

behind the bottom left corner of the fabric dispenser

drawer.

5. Remove indicator lamp and reed switch from con-

trol panel by prying gently with a small screwdriver,

being careful not to distort or damage control panel

securement tabs.

6. Remove the long dispenser connecting rod by

pulling gently at each end to remove.

7. Remove cam follower at timer by turning phillips

head fastener counter clockwise about 1/8 turn,

and pull to release.

8. Remove pivoting arm on dispenser by depressing

catch and pulling up on arm.

9. Remove water distributor by prying catch out

slightly with small screwdriver while lifting up.

10. To reassemble, use the triangular projections to

preload the spring before installing. Place the

spring on the rear projection then wind spring 3/4

turn and hook on small projection.

11. Next install water distributor by inserting hand into

the dispenser shell and hold water distributor in

place while pressing top portion into place. Water

distributor shaft is keyed and will only fit in one

position.

12. Release spring off front (smaller) projection to put

tension on cam follower.

13. The "a", "b", "c", notations on the dispenser hous-

ing refer to:

a = detergent chamber

b = bleach chamber

c = fabric softener chamber

The eccentric pointer should stop in the middle of

each chamber's bandwidth. If this is not possible,

center the pointer to areas "b" and "c", at the

expense of area "a" using the adjusting lever beside

center of pivoting arm.

To Remove or Replace Automatic Dispenser

«
...
29
30
31
32
33
...
»

Содержание WSXH208T




















































Отзывы:

Нет отзывов