
36
7. Remove screws (6) securing the control panel. Five of
the screws are located on the rear of the control panel
and one screw is on the front side, located behind the
bottom left corner of the fabric dispenser drawer.
8. Remove indicator lamp and reed switch from control
panel by prying gently with a small screwdriver, being
careful not to distort or damage control panel secure-
ment tabs.
9. Remove the long dispenser connecting rod by pulling
gently at each end to remove.
10. Remove pivoting arm on dispenser by depressing
catch and pulling up on arm.
11. Remove screws (3) from dispenser assembly, two at
rear and one on front. Release dispenser mounting
tabs and push dispenser rearward to clear front
opening. After dispenser assembly has cleared the
front opening, push dispenser assembly down as far
as possible.
12. Pull outer lip of bellows from front panel (glued in
spots). Remove wire clamp securing bellows to fill
spout. Removing and installing the fill spout clamp will
be a great deal easier if a simple tool is constructed
from a scrap piece of tubing. Partially squeeze one
end of a short piece of 3/8" or 1/2" O.D. tubing. Slip
the collapsed end of tubing over the twisted ends of
the clamp and rotate the tool one full turn to unlock the
clamp. If tool is hard to turn, wrap with friction tape or
duct tape to improve grip.
13. Remove bellows, reinforcement, and retaining spring
by pulling loose.
14. Install bellows reinforcement on new bellows.
15. Lubricate groove in replacement bellows with a
liberal application of liquid soap.
16. Install bellows by using a turning motion starting at
the top of the tub. At the same time apply pressure
to prevent the portion of the bellows already en-
gaged in the groove from popping out.
17. Once bellows is fully engaged in its mounting
groove, rotate to the proper location by lining up the
pointer (on bellows) with the 12:00 position on the
outer tub.
18. Install bellows retaining spring. This is done by
slipping the spring in the groove at the bottom of the
outer tub opening first. Stretch the spring while
guiding it into the groove all the way around the tub
opening and work toward top
19. Insert fill spout into the bellows. Reinstall wire
clamp on fill nozzle using tubing tool to twist clamp.
Make certain fill spout is pulled down as far as
possible which will aid in reinstalling clamp.
20. Reverse procedure to reassemble.
OUTER TUB
To Remove or Replace Outer or Inner Tub
1. Disconnect the washer from electrical supply.
2. If dryer is stacked on washer, remove clothes dryer
from top of washer.
3. If freestanding or undercounter installation, remove
the top panel.
4. Shut off water supply and disconnect water supply
hoses from water valve.
5. Remove rear access panel from washer.
6. Disconnect the motor wiring harness connector
block and ground wire. Remove wire tie to free
harness from tub.
7. Remove pressure fill tube from water level control.
8. Remove the front access panel.
9. Loosen clamp securing sump hose from tub and
Содержание WSXH208T
