manualshive.com logo in svg

GE WSXH208T, Техническое обслуживание руководство, Страница: 35 / 51

Поделиться
Скачать
GE WSXH208T Скачать руководство пользователя страница 35

 34

DRAIN PUMP AND MOTOR ASSEMBLY

The pump system consists of an AC motor and pump

assembly, a bellows type sump hose, air bell, and an

external cabinet drain hose.

The drain pump and motor assembly is mounted on the

base at the right front corner of the cabinet.

When the wash or rinse cycle is completed, the timer

energizes the pump motor to remove water from the tub.

The pump motor remains in operation throughout the

spin cycle.

To Test Drain Pump Motor Windings:

1. Disconnect the washer from electrical supply.

2. Remove front access panel from washer.

3. Disconnect harness plug from pump motor.

4. Check resistance of motor windings. Resistance

should be approximately 4.8 ohms ±10% @ 77°F.

To Remove or Replace Drain Pump Motor:

1. Disconnect the washer from electrical supply.

2. Remove front access panel from washer.

3. Remove bolts (2) securing motor cover to pump.

4. Disconnect electrical harness plug from pump

motor.

5. Remove clamp securing sump hose to pump.

6. Remove clamp securing exterior drain hose to

pump.

7. Remove two hex head screws securing the drain

motor and pump assembly to cabinet base.

8. Reverse procedure to install new drain motor and

pump assembly.

AIR BELL AND PRESSURE CONNECTING TUBE

In order to provide enough air pressure to activate the

water level control switch, a large volume of air must be

compressed and transferred to the water level control.

This is accomplished by using an air bell and black

rubber tubing.

The air stored in the air bell is compressed by the weight

of the water in the tub. The resulting pressure is then

transferred to the water level control through the  black

rubber tubing.

To Remove or Replace Air Bell:

1. Disconnect washer from electrical supply.

2. Remove two screws securing the front service

panel.

3. Remove the service panel by pulling down.

4. Remove drain hose from drain and empty any

remaining water in hose. Use a large pot or pan.

5. Remove clamp securing air bell to sump hose and

remove connecting tube from air bell.

6. Install new air bell and connecting tube.

7. Reverse procedure to reassemble.

NOTE: 

Seal air connecting tube to air bell and air bell to

sump hose using waterproof glue. DO NOT plug con-

necting tube opening.

Содержание WSXH208T




















































Отзывы:

Нет отзывов