GE WSXH208T Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 51

GE WSXH208T Скачать руководство пользователя страница 21

20

WATER LEVEL CONTROL

The water level control provides the proper amount of

wash and rinse water, but is not user adjustable. The

bulkiness of clothes is often more important than their

dry weight when determining a water level. Articles that

absorb a large amount of water, such as pillows,

blankets, and rugs require more water than indicated

when they are weighed. The water level control will

automatically provide more water with these loads.

The water level control is a pressure activated single-

pole, double-throw switch connected to an air bell at the

sump housing. A black rubber hose connects the

pressure switch to the air bell. Its purpose is to

determine the water level within the tub and control the

operation of the water fill valve.

WATER FILL VALVE

The two coil valve assembly is mounted on a bracket

and fastened to a brace at the upper right rear inside the

cabinet. Raise the top panel for access to water valve.

Under normal operating conditions, it takes several

seconds for the valve to completely close and stop the

water flow after the solenoid circuit is opened. This

prevents water hammer. The water valve flow rate is

4.50 GPM at 20 PSI and 7.0 GPM at 120 PSI.

WATER VALVE INLET SCREENS MUST BE KEPT

CLEAN AND IN GOOD CONDITION. A PLUGGED

BLEEDER HOLE IN WATER VALVE DIAPHRAGM

OR MINERAL DEPOSITS ON THE ARMATURE MAY

CAUSE THE WATER VALVE TO FAIL AND RESULT

IN CONTINUAL WATER FILL.

«
...
19
20
21
22
23
...
»

Содержание WSXH208T




















































Отзывы:

Нет отзывов